Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
hi
i create mesh network using the light switch client/server every things work well!
i have number of client and only one server.
i set the server to subscribe to the...
Hi,
i'm trying to sort out a performance problem I have with Android clients connecting to my nrf52832 using ble_nus service. Notice my problem is not about the absolute...
I am successfully using the ZigBee OTA upgrade example, but the firmware upgrade takes quite long, approximately a half an hour, so it is not an adequate time at the firmware...
Hi,
I'm using nRF52840 with SDK15.0.0 wit code from : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I could make...
Hi there! I'm an engineering student who is just getting started with all the ARM SoC's and BLE environmenment, in order to develop a project for college. The project that...
I try to test Relay performance of BLE mesh, my setup as following:
1 one client loaded light switch client;
2 two server loaded light server with Relay On;
3 one sever...
Hi, I'm looking to use the nRF9160 DK as an IoT Bluetooth Gateway as listed on the nRF9160's product page. Basically, I am tasked with connecting two nRF52840's (both in GATT...
Hi, I am developping a product with battery power. To preserve the battery life, this product needs to work in low power mode. How can configure nRF51 to advert in low power...
Hi,
I'm using the PCA10056 as a JLINK to my custom board. My board is powered by a LiPo battery through VDDH, and I have access to the SWD pins. I'm also using Segger Embedded...
I started from the blinky example for pca10040e (NRF52810) on SDK15.3, added some files and code to get TWI_MNGR working but i get an error which i can't solve
`.nrf_queue...
Hello
I am currently trying to read data and save the timings of it. When pushing a button on my custom made PCB, the microcontroller goes to the handledata function....
Hey,
So I've been using the Verizon SIM card supplied by nordic with our nRF9160 dev kit. I never really new how the APN was getting configured because it just happened...
Hi, I have DK-52840 where the ATMEL ATSAM3U2C is the on-board debugger. I replace firmware via my J-LINK ULTRA+ JTAG through 10-pin connector on-board, I used J-Link Commander...
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.2.0/hardware_driver_pwm.html
Where are more docs like this explaining how to use the drivers?
Hello, everyone, I am a fresh guy using nrf toolbox to read UART (52832) logs. Now I installed nRF Logger and try to save the UART log file. Does anyone can teach me how to...
