Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hiii...
I was working on ble_app_hrs example of sdk-6 using sd7.0.0. I tried to add broadcast feature by sending some hex values, dat was working, but now i want to display...
Hi,
I need to use 2 TWI bus (hardware constraint) so I wish to drive one bus with twi_hw_master.c and an other with twi_sw_master.c.
Each bus have their own GPIO. ...
Hello.
I'm reading the nrf51 Reference Manual.
in MPU section, [ (SWD) will no longer have access to code region 0 or code region 1, as well as no longer being able to...
Hello,
downloading the file nrfgo_sdk_2.3.0_setup.exe causes the virus scanner to report an issue and moving the file into a restricted zone.
Can you help on this...
hi, i made ble app with nRF51822 (s110), sdk 6.1.0
and i put this code after a pstorage_store() function to wait finishing of this function.
uint32_t err_code, count;...
My board is nrf51822.
Simple_uart works fine in uart_example, but once I copy it to my ble project which can work, it stuck.
Part of my code :
advertising_init();
services_init...
Hi all,
Now I'm using the nRF51822 DK and nRF Loader APP do the OTA.I can use the APP to complete the firmware update.However,the device
cann't go back to bootloader mode...
I'm trying to build an application on nrf51422 with s310 SDK ver5.2. My application is working fine with Bluetooth and now I want to add ANT service to it so can anyone please...
We are running OTA DFU bootloader provided in SDK 6.0 on nrf51822. We noticed that when the chip has been on for a while and we quickly power cycle it, the bootloader sometimes...
Thank you for your reply,Nikita
description of my system: Hardware:nrf51822,pca10001 Software:sdk5.20,run the softdevice s120
According to your reminder.i reference...
Hi,
We need to simulate the peripheral through PC, but with current version we cannot use 128-bit UUID which we need.
So the question is are there any plans to release...
Hi,
I want to init all 8 pipes in the host device (gazell protocoll) with a single init byte.
Thats important because i want to send that init byte to the devices with...
Hello,
as I know max number of simultaneous connections for s120 equals to 8. Is it software or hardware limitation?
Is there 'serialization' version of s120 (worked using...
Hi,
I use a step-down converter(not the integrated one) to generate 1,85V for the nRF51822 in my application.
When the applications starts the output voltage from the...
I use two nRF24LE1s as transmiter and receiver ,Here is my question:
1、I set the transmiter side to auto reply mode using PIPE0 ,but i found the STATUS regesitor to be 0b0001...