I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello.
I get error 0x10 (error for invalid flags) when i want to write to peripheral with my master module. I use the same code i always used, and i didnt change anything...
Hello.
I written code for nRF51822 w/ MPU6050 in S110(8.0.0) and Keil.
I tried to setup gyro as bellow.
twi_master_init(); => mpu6050_init(MOTION_SENSOR_ADDRESS);...
Hello
I have connected the nrF51-DK board and it was recognized by the computer.
I have managed to put in in a boot loader mode.
Since I switched it to boot loader...
I have three pca10001 boards. One is programmed as multilink central and other is programmed as multilink peripheral. when both peripherals are connected to central, the central...
I'm a newbie for Nordic development.
I just noticed that softdevice, app, and bootloader share the same CPU, RAM and Flash at the same time. This three software modules...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
Hi
the PWM frequency should reach 8MHz( duty cycle is 0.5 )when use timer0(16M) without SD.but i revised timer demo code from peripheral and only get 50KHz.i don't know...
Hi everyone,
I've found a few posts and a lot of info but I'd like to know if there is an existing example that merges a few of the examples found here ( github.com/.....
Hello.
I want to retain the value of a certain variable after issuing a system reset (sd_nvic_SystemReset).
Can this be done without storing it in the flash memory?
...
Hello.
I use SDK 8.0.0 and PCA10028 board. I try connect board to the Windows 8.1 PC ( i have Tablet PC and Desktop PC with BLE dongle). For connect board to Windows i...
I think I understand what these two flags do, the SYS one returns the system attributes, which I assume means data representing the CCCD for the service changed characteristic...
Hello,
Is there any compatible arduino lcd with existing library for the nRF51 Chipset?
So I can just plug it on the nRF51-DK, include the library and "lcd_wirte("text...
Dear Developers!
I'm a newbie in nrf51822
My Project needs to change between central and peripheral role. How can I apply OTA DFU with S130 soft device ?. In nrf51822 DFU...
