I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi all,
These steps broke my j-link lite! Is there a way to un-break it? Suggestions welcome.
I updated the segger pc software for another non nRF51 project (using a...
hi, nordic staff.
i'm working at s110(v6.0.0) and s120(v1.0.0). s110 provides notification and indication.
when s120 receives indication value from s110, s120 returns...
Hello all,
I successfully compiled and tested several examples for the nRF51822 Evaluation Kit on my Linux Box using gcc.
To do the same with my Smart Beacon Kit I downloaded...
I am trying DFU to work with gcc and SoftDevice 7.1.
Problem :
MCP able to send the APP binary successfully to the bootloader and DFU bootloader correctly write the app...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi, guys. Now I check the nRF51 IoT SDK(6lowpan, ipv6 over bluetooth).
nRF51 IoT SDK is needed Raspberry Pi, so I make the VMware Player Image for
Ubuntu 14.04.1 LTS 64bit...
I have a nRF51-DK. I would like to control the nRF51-DK through my mobile device.
What is the max. distance which can be reach with BLE(nordic chip)?
Is it possible...
Our application uses the S120 stack, and a bootloader. We want the bootloader to be able to update both our application software and the S120 stack (preserving the MBR). ...
Hi folks,
I have been successful in getting sample code compiled using Keil u-vision and MBED and installing it on nrfDK-51. It has become so simple to install apps - all...
Hi everyone,
I successfully compiled and loaded the experimental_ble_app_uart onto my pca10028 board.
I downloaded and installed the nRF toolbox on my nexus 7 tablet....
Hello everybody,
I want to do something very simple: Read some data from my Bluetooth peripheral. I know the UUID of the data I want to read, but I do not know the handle...
Hmm... this should be a simple question. But I haven't found a direct answer yet in the online SDK docs, the ARM NVIC docs, nor in this forum (and have only been confused...
Hi All,
I have a following setup :
The peripheral BLE device is supposed to send **(time critical )**data packets to Central device but the transfer is very rare (Can...
Hi,
I have modified slightly the OTA bootloader sample in SDK6.1 and SoftDevice 7.1.0. After flashing the bootloader code to the nrf51822 it works like charm, I can update...
when i use BLE_GAP_ADV_TYPE_ADV_DIRECT_IND mode,I can see the device advertise (MCP) but i couldn't able to connect with it (advertising_start at BLE_GAP_EVT_TIMEOUT)
i...
