I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello I am trying to implement AES Key Wrap on nrf54l15. For that i enabled ``` #necessary to get oberon_psa_wrap_key/oberon_psa_unwrap_key CONFIG_PSA_WANT_ALG_AES_KW=y #necessary...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Description:
I am experiencing a non-linear "sticking" and "jumping" behavior when attempting to monitor the VDDH rail using the internal VDDHDIV5 channel on the nRF52840...
I don't know where to make this suggestion, so hopefully my suggestion makes it to the right person.
I completed BLE Fundamentals and the nRF SDK courses.
I would have...
Hi! I'm migrating some code from an 14.2.0 SDK to the 17.1.0 SDK and cleaning up a big mess.
Whenever I call nrf_power_pofcon_set ( true , NRF_POWER_POFTHR_V27) with either...
I am trying to debug/flash an nRF54L15 using the nRF Connect VS code extension and a J-Link EDU. Although my J-Link EDU works fine with all the Segger tools, including Ozone...
Hi
I am looking to a wearable / health tracker which will be mounted on a persons head.
Are there any precertfied nRF7002 module where I don't need to go through the pain...
We tested several hundred connection and disconnection cycles with the nRF52840 BLE dongle. The first hundred cycles operated without any issues. However, at a later cycle...
Hello, I am trying to use twister + ztest to run some basic tests on my device custom project and nrf5340 Here are the contents. Current Directory Structure
Contents of...
Hello there,
I'm developing a project with NTN using a Vivo chip, a Brazil operator chip, but I'm having trouble with an nRF9151 and I'm trying to put it in NTN mode, but...
Hi
I took over a nordic project and was asked about the bluetooth version used in that project.
How Do I figure this out?
I am using a nrf52833. The firmware is developed...
Hi all
While connecting to a peripheral that has ble buttonless dfu characteristic i need to enable indicate.
Undortunately i get back err: 0x11(17) from sd_ble_gat...
I'm struggling with the nrf sdk v2.9.2 zigbee light_switch example. I copy the example, add this to proj.conf
CONFIG_ZIGBEE_CHANNEL=25 CONFIG_ZIGBEE_CHANNEL_SELECTION_MODE_SINGLE...
Hi.
I have a question.
When sending packets from a ZIGBEE product (with TI CC2538 built in) and receiving them with an nRF52840 Dongle (Sniffer FW) and Wireshark, is it...
Hello Everyone, I was wondering if there is any easy "ready configuration" way to directly set BLE advertising and connection interval with adding some config to the prj.conf...
