I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I now need to make a program on nrf5340 audio DK, SDK v3.0.2 to scan extended adv and print the BASE information in the subgroup in PA, without sink BIS, besides, a smartphone...
Hi,
I am following the course "nRF Connect SDK Fundamentals" and am almost at a standstill when it comes to progress.
I am still struggling with lesson 1 and lesson 2...
Freshly installed VS Code natively on Windows (also tried on Linux and WSL with same result) with NRF Connect Extension Pack, SDK 3.1.1, Toolchain 3.1.1 was used to create...
i get various answer about this, been in the rf design for a while, we used to make global antenna lenght on some give am ook circuit a tad shorter and then use a load cap...
Hi Nordic
I am working with nrf52840 and nrf52832 using ncs v2.8.0
I am trying to save coredump to flash according to instructions on this link - https://docs.nordicsemi...
Hi everyone,
I'm working with the nRF52840 using the nRF5 SDK v17.1.0 and SoftDevice S140 v7.2.0 . My application uses QSPI for external Flash communication.
I have some...
Hi,
i just noticed that for the nRF5340DK board, the file nrf5340_cpunet_reset.c has been removed.
Nevetheless it is still reference in the documentation online: https...
Hello,
We have built a device that uses the nRF52840 reference design shown below. With the configuration shown the board advertises as expected. If we replace either...
Hi, I try to use the example Bluethoot LE Wi-Fi provision in the nRF7002 DK and in the step to see the Wi-Fi Networks in the APP appers internal error.
Development kit...
Hi,
I'm developing a custom window cover device for Matter and I have a weird issue where Matter packets sometimes seem to take a very long time to go though. Window Cover...
Hi, It would have been quite useful if nRF54L15DK had CR2032 battery holder to carry around for experiments. since this board does not have it any recommendation to conne4ct...
I used the device tree to assist with schematic design, but after the PCBA was returned, I found that the peripheral functions could not be implemented normally.
It was...
NCS3.1.1, Windows10, VScode, NRF52840 custom board
With 3.1.1 I've discovered the paths in the "Edit build configuration" wizard are being broken and silently ignored during...
Hello DevZone,
May I know if there are any hardware SoCs and development kits that operate in Wi-Fi Halow(802.11ah) standard? Please point me out if there are. Thank You...
Hi,
I tested uart30 of NCS3.1.1, and found that I could not enter the low power consumption mode.But there is nothing wrong with uart20.
Related code usage:
prj.conf...
