Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
We are working with adafruit Nrf52832 and have a weird problem, the Ground pin and 3.3v pin is shorted and it also shows a 3.3v between them. Can you please help regarding...
Hi there,
I wanted to bring up the Bluetooth samples on NRF5340 development kit on NRF CONNECT SDK v2.2.0.
After building and flashing it, I can see the UART log on my...
Under:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_thread_tools.html#configuring-a-radio-co-processor
steps listed for 1 and "nRF52840 Dongle (USB...
Hello,
I am starting working on a nRF9160DK board, but I am new to this and I am a bit lost.
Using the Dev Academy course and example, I was able to make a small project...
Looking at the docs: nrf/ug_thread_architectures.html
I see the note "This platform design is currently discontinued by nRF Connect SDK." for "Network co-processor (NCP...
Hi All,
We have 2nos. of NRF5340 DK board, in which we are trying to run the "broadcast_audio_source" from nrfConnect SDK 2.2.0 sample installed from nrf Connect desktop...
hi team,
i have trying to wrote a code for saadc module in segger 5.40 using nrf52840 controller. whenever i am trying to increase the Acquisition time the sampling value...
Hi, I want DFU the NRF52840 using the UART. Please let me know the following quires .
Process-
I want to create two partition of memory one will store the my main application...
While running the mentioned code I am getting stack overflow error continuously. Can someone help me understand the reason behind that and what can be done to resolve such...
Hi, I am trying to do the SPI communication between a SPI master and two SPI slaves. I am using NRF52840 Dev Kit as SPI master and 2 ESP32-S3 as SPI slaves. I am using SDK...
I have added WDT to the blinky_freertos sample.
And I am debugging with SEGGER ozone.
building with SDK17:
If you reset the software in the debugger and start it,...
I have this 2,4" TFT Display with a IL9325 driver! I need to implement a 8bit 8080 Parallel interface.
image description
This is my 8 bit write function:
// Write...
I have this as nrf52840dk_nrf52840.overlay in my application directory:
/ {
lightStrings {
compatible = "gpio" ;
lightString0: lightString_0 {
gpios = <& gpio0...
Dear Sirs!
I am going to use nrf_drv_spi_xfer to read 15 bytes periodically (Approximately each 4 ms) according to GPIO (GPIOTE Event via PPI). To do it I am going to call...
