Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I'll start off by saying, as a new developer, Nordic has made an absolute mess out of the docs. The default example 'TWI_sensor' starts with easyDMA enabled, meaning it defaults...
Hello,
I am using nrf5340 module with external hardware audio codec to test stereo audio output.
I use nrf5340 module as the headset to connect with Pixel 7 mobile phone...
Hi Nordic Team,
The default stream direction is undirectional, so I add CONFIG_STREAM_BIDIRECTIONAL=y in prj.conf, then use " python buildprog.py -c both -b debug -d both...
Hello,
We have a fitness application that employs concurrent use of ANT+ and BLE communications on an nRF52840, that we wish to port to the nRF5340. The product brief...
I created a custom bootloader based on the SDK 15.3.0 secure bootloader. At location 0xFF8 I defined the uicr bootloader start address as 0xE4000 but my bootloader actually...
Hello
I was trying to add BH1749 I2C Sensor for existing Mesh_Sensor example to get RGB values like shown in this Light_Sensor example. Couldn't decide how to do it and...
Hello all,
Environment: nRF52840-DK, NRF SDK V15.0.0, SoftDevice s140 v 6.0.0, ARMGCC building with Makefile
I am currently trying to combine the examples of the USB and...
On a 52840 USB stick, I successfully tested the "observer" demo app.
Now, I tried to extend it by enabling CONFIG_BT_EXT_ADV=y which is supposed to print some details about...
Hi, I got strange error which I can't to fix.
From time to time, I get the same readings from every function which counts the CPU cycles. They all base on DWT_CTRL. Board...
Using NCS SDK v2.1.0
Example Project: nrf/samples/bluetooth/peripheral_power_profiling
Building the example project gives build warnings:
Could you help me understand...
Hi,
I am trying to implement a Low Power Wireless technology to get sensor values from more than 10 devices at a time. On doing research, I found that the Thread Topology...
Hello, we have built a custom nRF9160 board with different populations for the GPS antenna, now we would like to do some tests to find out which variant offers the best signal...
Hi!
The posts I've found regarding this were quite old, and they mentioned features which then were coming.
So I'll ask anew: Is it possible to use AT-commands through...
Hello,
I would like to ask you if SoftDevice S132 v.7.x.x allows Master-initiated Feature Exchange procedure?
BLE Core spec: Vol6, Part B, Cap. 5.1.4.1.
I tried to find...
Hi everyone, I use nrf52833 to make dongle. My test found that after suspend of usb, I tried to enable ESB rx mode, but I couldn't receive rf data. What is the problem?The...
