Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello Nordic Team, I have referred this post and am aiming to create an empty bare metal project on nrf54L15 for BLE peripheral with GAP read, write, notification and idicate...
HI
I am currently using nRF54L15 with NCS 3.0.0 SDK, running the periodic_adv_conn example. I made the following modifications to the extended advertising and periodic advertising...
We have noticed an issue with our device built on nRF5 SDK + nRF52832 when connected to iOS 26.
Initially after connection, everything is ok. Then we attempt a connection...
I am porting nRF SDK 2.6.1 to SDK 2.7.0 on the nRF5340. For the network core, where exactly should the kconfig (prj.conf) file be located and named? On the sysbuild migration...
Hi, based on the previous struggle with data transfer drops with nrf9161 ( ) we came after the cooperation with Vodafone MNO to the situation, that (at certain test place...
I'm using the peripheral_bms project. The only change being in the overlay to make it work with nrf52833 dk. I'm able to connect with nrfConnect and see the services (except...
I'm developing with the NRF52840 using IAR Embedded Workbench , and implementing wireless communication based on the IEEE802.15.4 Zigbee protocol .
In the MAC frame layer...
I am new to Nordic and want to design with the nRF52840. I have read this guide:
used AppCAD to find the best width and clearance for the ground layer, but when I downloaded...
Hello, I am using NCS 3.0.2 on nRF52840. I have been using MCUBoot for a long time on my device, and it is working fine. Recently, I went through a requirement where I needed...
Hey everyone,
I've been trying to get the Bluetooth Mesh DFU Target sample working on my nRF5340 DK and running into some issues. I've read through the docs.nordicsemi.com...
Hi All,
I have an nRF5340 Audio DK which has problem with the network core. When I connect the USB to board or try to recover the board the MCU light at the bottom of...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's and I want to have the same functionality of the walkie talkie demo but instead use the microphone of the...
I had a working Matter application, but due to some human error, I erased my WSL installation.
I set it up again, but after successfully flashing my code onto the Nordic...
Hi,
For a product currently under development, we need to use a counter as an RTC. We’re targeting the following commit in ncs/sdk-zephyr :
github.com/.../d7e41fd2e361ee15454a253ebec9bb37aceaf09f...
