to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
I try to run https://github.com/NordicSemiconductor/pc-ble-driver/tree/master/examples/nordic_uart_client But the following error occurred.
D:\pc-ble-driver\build\examples...
Hi,
I am testing an app using CoAP client/sever. I want to redirect the RTT log messages to UART0. I had a look at https://devzone.nordicsemi.com/f/nordic-q-a/32058/why...
Hi,
Currently, we are facing a huge problem with our custom boards. Between different boards the ADC values varying very much even with a given voltage input.
For instance...
Hello all
I am porting the code from the nRF52DK to the nrf52820, and so far so good, however, I am having a question, when configuring the TWI, will this get me the right...
Hi all,
Provided the nRF52840 board implements up to 4 SPI, I would like to use at least 2 of them simultaneously. I need to do it like this because I need one of them...
Hi, I am trying to merge Libuarte with the FreeRTOS environment. I am trying to use RTC-2 for libuarte and RTC-1/0 for Freertos. I am not sure what other things I should enable...
I'm working on a custom board that uses an nRF52832 module. It has a single button that is used to power the device On/Off and a >= 5sec long press from Off to force enter...
Hello,
we would like to use a pin on GPIO P1 as GPIO in non-secure mode, but only found the solution stated in this thread yet: https://devzone.nordicsemi.com/f/nordic-q...
Hello,
I am experiencing issues with an nRF5340 board and its SPI.
I am trying to add an Pmod OLED (128x32) screen to my board, but firstly I am trying to set up the...
Zephyr nRF52840
I am working with 2 nRF52840dk. The master side seems to be working as expected. i have monitored it and seen clock, MOSI and CS all working as expected...
Hello,
I have a debugging issue with VS code IDE.
Suddenly, i cant debug with an error:
However, flashing board is working succesfully.
What am i supposed to do...
We use spi flash with custom driver and goal is to set it to act as secondary partition for MCUBoot.
The question is how to adapt driver to be accepted by MCUBoot, maybe...
Hello,
First off, thank you for reading this. I know this is on the cutting edge, so bugs are to be expected.
Problem:
I loaded the dm sample found here: https://developer...
Hi,
I am using nCS and mcuboot in my application for development, on nRF52833.
I build a nCS project, the build bin file (prj.conf as ):
I broke up into packets...
