Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi,
I'm using a nrf52832 and NCS 1.9.0 and I would like to be able to use SMP to make firmware updates using BLE. I'm was able to perform FOTA, but the flash is divided...
Greetings!
We are trying to troubleshoot occasional hangup issue. We run the app in debug mode. When it hangs up, we hit pause and got the followings in the Call Stack window...
Hi,
I want to use nrf5340 dk board to debug nrf52840dongle, i have connected two board with a cable and have checked the signal is good( nrf5340 debug out p19 ------ nrf52840...
Hello all
the BLE module with the nRF52820 is programmed with a ble_app_uart_pca100e example from the nRF5SDK ver 17.1.0, according to the RSSI graph it seems it works ...
Hello Reader, I noticed two almost similar modules " DK buttons and LEDs" library and the "CAF LED & Button" library (or module). What is the difference between DK buttons...
I get the following error message from my device
àÓ FATAL: Exception occurred in Secure State [10.2 10:01:52.062]FATAL: ***** HARD FAULT ***** [10.2 10:01:52.062]FATAL:...
We have both native iOS and Android-apps that handle DFU-updates of our BLE-FW on our HW-devices. We are currently experiencing a dip in success rate (according to our firebase...
Hey Nordic,
The following are some specifications of my project.
nRF52833-DK
PCA10100
Softdevice is S122
Based on "ble_app_uart_c"
SDK 17.1.0
I am using VSCODE...
While testing a new nRF9160 based product with a Hologram SIM card, it connects fine in Minnesota, USA, but not in Winnellie NT, Australia.
Do you have insight into why...
Hi, I am using nRF connect sdk1.9.0 and modem firmware 1.3.1.
I have configured GPS to single fix mode.
err = nrf_modem_ gnss _fix_interval_set ( 0 );
err = nrf_modem_...
I have been trying for hours to get the LTE Sensor Gateway sample to work on my Thingy:91 (PCA20035) without success. According to the v2.0.2 README and the HCI low power...
Hi,
I would like to create a service that shows the current TX power of a peripheral during connection. I am using the Android nRF Connect app to connect to the nRF52833...
Hi:
I can't find the download address and description of the S110_NRF51822_7.1.0 protocol stack on your official website. I would like to know the version of BLE of this...
Hello, I encountered some issues with VS Code nRF environment. Kconfig will not open when clicked nor can I debug. When I try to debug it seems to be launching debug for a...
Hi
How can I read out the bootloader version from the main application which I defined in the zip packet (or merged hex) with nrfutil?
rfutil pkg generate --hw-version...
