Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello, I'm using nrf mesh serial example in nrf5sdkformeshv500src, in the serial node i subscripted to 0xC000 but i can't not received messages more than 32 node, my netwwork...
Hi All,
Sorry to ask this question, I just learned a little about cmake.
Now I wanted to add a few src files based on the light switch example in SES. Do I have to create...
Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hi.
I am trying to update my Softdevice using DFU.
If I update from S112 to S140, do I have to upload the application as an image built with S140 as well?
And do I need...
Hi there,
I can't seem to add header files to my project.
The header files underlined in red are not from the Nordic SDK installed from the Toolchain Manager.
...
Hello,
we are currently developing an MQTT Bridge Application. We plan to use a nrf52840 in combination with the nrf9160 as our Bridge which is going to send its data...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
I have developed my thread application based on nrf_sdk_for_thread_and_zigbee and implemented DFU OTA in my application. It is working fine with no issues.
I am using nrf52840...
Hi,
My nrf52840 is not detecting the USB, i tried by pressing the SW5 after that bootloader led starts blinking but not showing any drive in the PC also
can you please...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
I have an applications that was using NCS 1.7.1 in its west manifest. I am going through the process of upgrading to 1.9.1
My application using zero latency IRQs and sets...
When I use two nrf5340 audio DK to test the LE audio demo, the handset side always crashes. Especially when I move the DK that is used as the handset.I think that incomplete...
I am trying to interface the Grove 4 Digit Display(TM1637) with the nRF52840 DK.I have successfully interfaced it with ESP32 and get clear output after researching for the...
The main loop in our nRF9160 (NCS v1.8.0) is a typical main loop with semaphore following https://docs.zephyrproject.org/latest/kernel/services/threads/system_threads.html...
Hi
I attempted to create a 32.768 kHz signal from the nRF52840. When I use the HF external clock: NRF_CLOCK->TASKS_HFCLKSTART = 1 ; the generated clock signal looks great...
