Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Good afternoon,
I am working with the NRF9160-SICA-B1A-R module on a custom board.
Checking the functionalities with a software developed on a Thingy:91, I get the following...
Hi, I have recently upgraded to a new system with windows 11. I have been working with NCS v1.8.0 on last system and installed the same in new system. all the necessary installations...
I have downloaded the WS2812 driver example and have successfully been using the nRF52832 DK to control these lights with SPI. I am ready to start developing on a custom board...
This was driving me crazy. nRF Terminal extension in VS Code just silently fails. I was able to use the JLink Viewer app so I knew RTT was working correctly.
I then looked...
Hi, I am using nrf52840 to senda imu data over bluetooth to computer. For the transmitter i am using NINAB306 with integrated PCB antenna as a central i use nrf52 dongle....
Hi,
while switching to the nRF Connect SDK, I cannot program anymore my ANNA B112 (which is a nRF52832) using my nRF52840-DK as a programmer.
The following are working...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
Hi, There, I use 52832 to develop a HID touch(single point) device, it can work on android & windows, but can't work on iphone13(ios15). It can connect to iphone, but no touch...
Greetings,
When trying to perform an http GET command over LTE-M (using the "Curl" MoSh command, to trigger a http download of a 500Ko or 1Mo file) after a few successfull...
I'm using three low power PWM instances driving three separate IO pins open an nRF 52810 and need to be able to re-configure each of the channels on the fly to select opposite...
In order to protect my device from becoming bricked when APP and NET side implementation of RPC application differs, due to wrong version being flashed or OTA fails on one...
Hi,
I'd like to implement Keil RTX5 on my custom BLE project for the nRF52832 using the S112 SoftDevice v7.2.0.
We are looking to standardise as many of our projects as...
In my schematic design, my nrf5340 uses vddh power supply mode, and the output VDD does not mount any load. Is it necessary for me to connect each VDD pin together during...
I'm using NCS 1.9.1 and Segger SES
Following Nordic's recommendation I first made a copy of BLE/peripheral_uart in order to preserve the original code and then used the...
Hi everyone!
Could anyone clarify a few questions regarding channel mapping?
1. Is that true if I want to use specific BLE channels I need to do it just once on a central...
