Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi everyone, I made a custom class composite device. The firmware seems to work except for one thing I can't fix. If I initialize the USB in the following way:
If instead...
I am using nRF52840 DK and I run my project using VS Code.
I wanted to run MPU 6050 accelerometer example for my DK. Below are my configuration I had setup for running the...
Hello,
I have been trying to use some of the direction finding examples for the nRF52833 and I was wondering if there is a timeline for when soft devices will start supporting...
Hello,
I am reading the FIFO buffer of a sensor via SPIM3 with nRF52840. What I want to do is that by the use of PPI, the start of the transmission (PPI channel 0, to TASKS_START...
I have to use TWI and PWM modules at the same time. When I use them in two separate projects thy worked well in their respective applications. But, when I combine them in...
In the beginnig of this year I used to test my edge Impulse Zephyr project with nRF connect Segger Embedded studio and it's worked, but now days I having a problem with Segger...
On Zephyr 2.7 I used following snipped to connect a GPIO pin (ADC_nDRDY) to a SPI TASK (simplified):
On Zephyr 3.0.0 we experienced immediate crashes.
I then saw that...
The RPM package for Linux x86 64 bit has its architecture set to amd64, but the correct value should be x86_64. This problem prevents installing the RPM on current versions...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
