Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello,
I have made a lot of work with nrf52840 microcontroller and i am in pre-production stage.
NRF Connect is not loading in vs code.
I have tried to uninstall/reinstall...
Hey,
I am using an HID keyboard + keyboard toggle in my project,
When the nrf connects an iOS phone, it takes control over the phone's keyboard.
To release the kb we...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
I am trying to get a PWM waveform output at 50% duty cycle with 409.6kHz frequency based on...
Hi,
I have a NRF52840 USB dongle( https://www.nordicsemi.com/Products/Development-hardware/nRF52840-Dongle); is Any possible to flash NRF52840 dongle with PTS Firmware Upgrade...
NRF52820
PAN1781 EV Board
Segger Embedded Studio 5.62
nRF5_SDK_17.1.0_ddde560
S140
Hello,
I'm currently working on an indoor positioning system and as the title...
Hi,
I compiled an application that should start at address 0x40000. However, executing an OTA DFU always places the application at 0x26000, right after the softdevice. ...
In a previous ticket on another topic this question came up. Given it was a tangent to the original topic of that thread, and I think it would be helpful to others, I decided...
Hello,
I have a battery with 4.2v max charge. Since this is outside the input range for nrf52832, I have to add a down voltage regulator. Now the question is: Should I...
Hi!
I need to modify the code of the secure and the non-secure images of my project.
I tried to follow this guide https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
Hi
I have a project which is using 53832 as the master , main 52832 works with smart phone by bluetooth ,and broadcasts ebike information throght the ANT+ .
I would...
Hello everyone
I have a bunch of custom dongles from the company I work for and two of them started to behave in a strange way after I tried to erase and program them through...
Hi,
I'm currently in the evaluation phase of a project and would like to use a NRF52 chip, but I need to ensure, that I can use two independet hardware timers. I had already...
I am running a PWM pin on 15 using this DT Overlay:
pwmnmos {
compatible = "pwm-leds" ;
status = "okay" ;
pwm_nmos0: pwm_nmos_0 {
pwms = <& pwm2 15 >;
};
...
Hello,
I built my application based on your "ble_peripheral_lbs_coex" example. Board is nRF5340DK.
Mesh and BLE (NUS service) run together but I noticed that the NUS UUID...
