Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I have developed a Zigbee application using the nrf52840 DK board + nRF Connect + Zephyr and it is working. Now I am trying to move that app over to the nrf52840 dongle. It...
Hi, I am using nRF52832 development board and I have a motor driver. Motor driver has external power supply, I am just using nRF52832 to set directions which consumes low...
Hello, I am trying to use the dfu library to update the nrf52840 with a firmware stored in a littlefs file in an external qspi flash. I can successfully read the entire firmware...
Dear Nordic team,
it is very important for the RF and the HW engineers to be able to know the current transmit power of the modem. That will help us evaluate the network...
Hi
I'm looking for an example implementaion code on the nRF52840 without an operating system. Is there some example or application note?
I connected the SPI and all IO...
Hi,
I updated to VS Code V1.65 today and had some strange behavior with the NRF connect extension for VS Code.
After updating, clicking any "Action" in the sidebar (e...
I have already implemented DFU update in our one product. Which have fast USB interface and fast "lag-less" UART interface to nRF chip which is used as our bluetooth central...
I am using a code based on nrf52-ble-app-uart-c-multilink ( https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink )
If the central is working and the peripherals...
Board: NRF52833 (PCA10100)
SDK version: 17.0.2
Softdevice: S122
I am trying to perform USB DFU for my application. As I am using nrf52833 board, there is no available...
Hi ,
SDK 17.1.0
SD132
SoC - nrf52832
I am following the below given link to create custom service.
https://github.com/bjornspockeli/custom_ble_service_example...
We plan to use it with the Converter mode enabled for low current consumption.
However, if PIN is always set to Hi in order to use the Converter mode, about 300μA will...
After a lot of thought about the issues with TCP under EDRX or PSM , I have a feature request.
I would like if the application layer could know when a TCP socket was sitting...
Hi Nordic team
I tried ncs 1.9.0 peripheral_uart sample (\TOOLCHAIN\v1.9.0\nrf\samples\bluetooth\peripheral_uart) at PCA10095 v1.0.0 DK.
1. Application core: Board is...
