Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello
I am planning to purchase Nordic Semiconductor Power Profiler Kit. Before purchasing the kit I need to know, Is this kit supports another company's microcontrollers...
I am using nrf52832 with a custom board with no external crystal oscillator. As bootloader I use "secure_bootloader_uart_mbr" so I don't have softdevice. SDK is 17.1.0_ddde560...
using ble_app_interactive on one dev kit and connecting to pc viewing on terminal
other is my perihperal.
on entering connect <device address> it gets disconnected
hi I sucessfully tested the blinky project on the nRF52840 dongle... btw i'm using vanilla zephyr...
but i'm unable to prototype the uart comm on this board... the board...
I'm working on NCS 1.8.0.
I can use DFU APIs to upgrade my firmware successfully, however, after DFU is finished and system reboot, the McuBoot to swap images is too slow...
Hi, I want to know brief aboout difference and objective of different types of Zephyr projects. When using nRF Connect SDK, in SES a project is created, 3 options are available...
Hello,
I am using the nRF52840 DK board and writing code in Zephyr and I want to change the clock frequency. Currently, I guess by default it is 32.768KHz How can I change...
Hi,
I am using an nRF9160/nRFConnect SDK 1.8.0/VSCode and my application uses MCUBoot and SPM. It is a "non secure" application.
I am trying to get a reset cause.
hwinfo_get_reset_cause...
Hello,
We are developing a product based on the nrf52840 chip with our own antenna design. we would like to register our product in SIG and obtain a company identifier ID...
Hi, can nRF52 DK or nRF 52832 read data from other sensors, for example, accelerometer, gyroscope and heart rate sensor. Accelerometer and gyroscope would have an implemented...
Hello.
I would like to know if its possible to preform a firmware update from the application itself like so:
1. Getting the firmware via UART in chunks of 2k (from a...
I am following along with the BLE DFU tutorial found here https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu but when I attempt to build...
Hi,
We have a custom board with the nrf5340 SoC, after erasing it with the erase function included in the nrf extension for VScode, we started getting the following error...
NCS 1.8.0
We have a custom board that uses the ATECC508A on an I2C bus. We are using release 3.3.0 of Microchips library cryptoauthlib which includes zephyr hal support...
