Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hello everyone, I'm developing a wearable device based on nRF52832 which reads IMU (ICM20948) data using TWI.
The problem is that if I try to use the code with a custom...
hello everyone,
in my project i need to advertise the sensor data as well as connecting the BLE TAG . in detail i am using nrf52810 with mpu6050 and i want read the accelerometer...
Hello,
During my evaluation of nRF52840 I discovered an issue which prevents the device from joining a Zigbee network successfully.
I'm using out of the box zigbee/light_bulb...
Hi,
I've installed all by the book watching the installation videos and I have a problem building in VScode
when I try to build with nrf connect app window I get this...
Hello,
To preface, this project was redirected to me and I have very little experience using SoCs. Happy to provide any additional information and apologies for issues in...
Hi!,
I am trying to create an application with BT Mesh using the nrF52840 DK and two nrF52840 Dongles with an OnOff Model Server and an OnOff Model Client respectively....
Hello.
I am new to Zephyr, I know how to digital read the pin which is used as INPUT
#define SW0_NODE DT_ALIAS (sw0)
static const struct gpio_dt_spec DOUTINPUT = GPIO_DT_SPEC_GET_OR...
Greetings,
I'm using NRF52840 with softdevice and nRF5_SDK_17.1.0 on NRF52 DK.
The shutdown_handler in my code is as follows:
There is a secure bootloader from Nordic...
Hi, I am using nRF52832 module as connectivity chip (GAP peripheral, GATT server) with ble_app_uart_pca10040_s112 as source.
I am using nRF connect app to test data communication...
I am currently developing a feature for a BLE module to pass certifications (BL654 Laird, based on nRF52840). My application runs on SDK 15.0.0. I used the "radio_test" module...
My overall goal is to update the percentage of battery left in the advertiser and then either go to a nine second sleep to conserve as much power as possible and then wake...
I am following the instructions to enable micro-ecc support for an example code ( secure bootloader ble s132 pca10040 debug). I am using SDK 17.0.2.
I have successfully...
I'm sorry, maybe it's me, but your SAADC documentation leaves much to be desired, as I was easily able to implement getting readings from a single analog input (non-blocking...
Hi,
Trying to do a very simple thing.
I want to start a new project from a sample project, but I want my new project to be in a different folder
Load nRF Connect...
Greetings,
I've been developing a nrfxlib/zboss based Zigbee device and hitting a wall when trying to add more than one endpoint of a given type .
This is because the...
