Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi we are developing a prototype with NRF5340DK, for which we needed to control few set of GPIOs. we wrote our code in the assumption that it's pretty straight forward and...
Hi,
I just updated my vsCode extension and the visual devicetree editor stopped working
I can compile just fine but changing the DT will prove difficult from now on. ...
I used the official example provided by Nordic: github.com/.../nrf70-wifi-ble-image-transfer-demo . I followed all the instructions to complete the preliminary configuration...
1. can you tell in detail about Easy DMA supporting on SPI, I would like to understand how I can utilize DMA feature for communication with RAM over SPI what is the added...
Hi
We have nPM1300 evaluation kit, we use SW1 VOUT1 1.8V as VINLDO1 input, we remove jumper JP7(for LS_LDO_OUT1 connect to R8) on P15 connector, and provide 1kohm loading...
We just started a project to replace an old PAN1720 and decided to use the nRF54L15 based module. So I am just getting started with the VS code and zephry enviroment using...
The UART (Port 2) gets garbled after bt_enable(). This issue does not occur if actively Debugging using Segger.
The issue is also reproducible upon a settings_save_one(...
Hi,
I am using nRF54L15, SDK & Toolchain as 3.0.2 version This is for Hid Keyboard, the problem I'm facing is once connected to one device, manually disconnecting & connecting...
Hello,
There are some issues I have found when I tried to achieve both BLE and ESB features concurrently on nRF54L chips, and some of them I have figured out how to fix...
I have BOARD_ROOT set in both zephyr/module.yml and in CMakeLists, and in my boards folder I have a custom board "boards/nordic/myboard". I have all the necessary files for...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
Hi Nordic team,
I’m building an LE Audio gateway on the nRF5340 DK using the TMAP_Central sample (NCS v3.0.2, with minor local changes). The setup captures audio, encodes...
I'm working with nRF52840 microcontroller, nRF SDK 17.1.0 and Softdevice S140 version 7.2.0
The peripheral devices sends 29 bytes of data with a BLE notification from a...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I'm currently using firmware advertising/scanning with 1M PHY, but I'd like to use Coded PHY instead. I tried changing the advertising parameters as shown below, based on...
