Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello, I am using NRF52840, I tried to use Jtrce for debugging but the results are unreliable due to design of the nRF52 target device in regards to the trace clock speed...
Project context: -------------------- Server BLE for home trainer diy Target (Bluetooth server) : Bluefruit nRF52 The feather Library : BluefruitBLE Client : nRF Connect ...
Hello,
I am in the process of writing a custom application for a custom board for the nRF5340, but have run into some odd behavior with SES when I started changing around...
Hi,
SDK 17.0.2
I notice a startup current sequence (shown below) which is consuming around 8.3 uJ. I would like to know what operation on startup is causing this surge...
I've added:
zephyr_code_relocate(src/main.c SRAM)
and
CONFIG_CODE_DATA_RELOCATION=y
However, this only relocates by main to RAM. Vectors, kernel, etc, are still going...
Using 52840, I would like to drive an ADC chip - and it needs to get 800KHz. sampling speed (800/16=50KHz) should be accurate
* a timer isn't an option - not accurate enough...
Hello,
I have a Thingy91 which was previously successfuly paired to nrf cloud. I deleted the device from nrf cloud and provisioned new certificates from nrf cloud (and uploaded...
I am trying to set up a peripheral connection between an nRF-52840 and an iPhone via my team's iOS app. The board connects normally via the Nordic Connect app and shows the...
I have configured the server with max mtu size of 512 and changed the start location of the app to allow for a larger SoftDevice. I have done this both for an mtu of 512 and...
In one of my projects, UART interface is used for the communication of external sensors. During the power consumption test, I found that when 9160 enters the idle state, its...
Hello,
I am having nRF 52840 SDK for which I am able to control leds of sdk using ble app blinky example through android mobile.
Mean while, in nRF mesh provisioner example...
I'm having a bit trouble here getting migrated to LPUART on a working nRF9160 <> HCI BLE on nRF52 (On the Thingy91). As far as I can tell my .conf and .overlay files are what...
Hello,
I've run into a problem, which seems at least to be similar to that described in another thread . In short, if I set up a counter with CC[n] and start it, a COMPARE...
Hi,
I would like to store important information (few MAC addresses) in flash memory at manufacturing stage. Then my program will be able to read these information thanks...
Hi ,
My environment:
nrf5340 DK board
nrf connect SDK v1.5.0
segger Studio IDE
I would like to establish communication from application core to network core...
