I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
hello,
i find a mistake line 62
"ldr r0, =%4 \n" ->>>>> The '=' should be removed .
void app_error_handler(ret_code_t error_code, uint32_t line_num, const uint8_t...
modem fw 1.3.0
ncs 1.5.0 and master
I am trying to test modem firmware upgrades using the lwm2m client sample and every time it is writing the 20% downloaded chunk, the...
Hi, I am following the tutorial and have some questions during the implementation.
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0
A red led...
Hello There,
So basically I need to send and receive and data from to Serial Terminal via FTDI module to nRF9160 DK. So for this I am using ncs\v1.5.1\nrf\samples\peripheral...
Hi.
After updating Programmer of nrfConnect to v1.4.9, I have not be able to "execute Erase All" command.
Error message is "Error: Error occured when program. Errorcode...
Dear Nordic,
how to set UART/USB console output to be non-blocking? We use printk() to output some debug info to USB console. When the USB isn't connected, the program stalls...
Dear Nordic-Support-Team,
I (software developer) work together with an electrical engineer to develop a device, which will incorporate the nRF9160 SiP. The firmware/application...
Dear Nordic Engineer
I currently have a project that requires 5340 to act as an MCU. I also need to plug in a FLASH, which is 4GBIT NAND FLASH. Is there an example of supporting...
Hi :
nRF52832 PCA10040 DK burn this link hex code: https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE/Download#infotabs
Can...
https://devzone.nordicsemi.com/f/nordic-q-a/49269/long-range-nrf52840-central-can-t-connect-with-peripheral-in-ble_gap_phy_coded
due to this problem recently I have problem...
Hi Nordic Support Team,
I have asked this question previously, but I might as well make another post to collect my experience with this problem this past month. I will try...
Hello,
Here is my configuration:
NRF52840
S140
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247
I would like to enable DDLE in order to get more than 27 bytes in each...
