Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi,
I was reading the values from the FICR of my nrf9160 on my thingy91 and I noticed that when I read the INFO.PART register from the FICR, it returned 0x00009120 rather...
we have BorderRouter- Raspberry pi flashed with nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design .
As an end device I have EFR32 MG12 WSTK flashed with OT-CLI...
I am developing application with buttonles BLE DFU and FreeRTOS. I needed debounce on buttons and decided to use app_button. Here is my init:
I turn on log debug on app_timer...
Apologies for this question, as it has been asked a number of times but I've not found anything to help so far.
As at the time of writing, I believe I've got the latest...
I'm trying to deploy a new firmware to my hardware device but I get the following error in the nrf Connect 3.6.1 programmer (v1.4.8):
16:47:36.937
Error when getting...
Hi,
I noticed that the PPK2 turns off the internal voltage regulator upon disconnecting from it. Is there a possibility to change that behavior? I would like the voltage...
Hey Guys,
I have the nrf52840 as the peripheral and my application use varies depending on which central I am connecting to in terms of:
PC ( Windows or macOS or Linux...
Hello,
I have been recently trying to initialize fds in my application, through the assistance of the given flash_fds examples in the SDK (15.3).
Currently, I'm coming...
Hi, I'm working with flash, I've started with the example code from flash_storage, as I will need to use flash while using a SoftDevice.
I use NRF52 Dongle and SDK17.0.2...
hello,
i am using nrf52840 dvk with sx1276 lora modules and trying to read my device address using spi i am just calling the below function in main
uint8_t spiCommandData...
Hello everyone,
I'm currently working on porting a device driver to Zephyr on the nRF9160. I have defined a device tree and set up the device through the .overlay file...
Hi
I was wondering if there is any further reading about the Automatic network selection set as <mode> in the +COPS set command.
Especially, I'm looking for a solution...
Hi,
I just recently began implementing the mesh stack into an existing application, using mesh v3.2 and nrf sdk 15.2.
Integration works well by using the integration guide...
I am currently working on nRF52DK and TCAN4550 using SPI communication. Regardless the SPI slave which I am using, I have some doubts with SPI Nordic library (I am using 17...
