Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Today I am attempting to set up an MQTT connection from a Thread device to an MQTT server on the Internet (for better or for worse, if this is a terrible idea I'm open to...
Hey
Im trying to as low power consumption as possible and for that i have found that sys_poweroff() gives me that.
My problem is that i cannot get a pin state change...
I work on a project where we make a device with a 9160, and our application is build using NCS 1.7.0 and is programmed with MFW 1.3.0. The network our devices connect to is...
I have basically all my code disabled, all I do in main() is get a pointer to the "zephyr_console", suspend it and return.
This gives me an average power consumption of...
Hello,
I try to dfu with mcumgr but I feel like the download speed is a little slow. So I want to increase download speed. I think that mcumgr has the command to set boudrate...
Hello,
We are designing a board with a nrf5340 with a VDD of 1.8V.
The board is very small and it's complex to fit all the components on it.
We are thinking of removing...
Hello,
I was wondering if there is away to perform DFU using SPI without smp protocol or mcumgr from one nRF52840 to another? What I am trying to do is to send a firmware...
Hi,
We are trying to attain power optimization in our project, which uses the nRF5340 board. In our code we have implimented RTOS, BLE for data transfer and are using i2c...
Hi,
I encountered an issue since i upgraded nrfjrpog
My previous version was 10.13.0
And now is 10.24.2.
I have a batch file to program my device and until the upgrade...
We need very fast Wi-Fi transfer rates at times. I have been able to tune the code and Wi-Fi driver settings to get up to 30-35 Mbps which is great. But if I don't throttle...
Hi,
Added a function to the coap_client sample code that executes otInstanceFactoryReset by pressing a button and sets it to factory shipping mode. However, it appears that...
I'm developing a system where I want to connect simultaneously to different BLE and ANT+ sensors. I'm using the nRF5340 DK and I would like to be able to select which sensors...
I have a project that I'm pulling in code from multiple_adv_sets using v2.7.0 and sysbuild.
talks about the opcodes and status being in the spec? https://www.bluetooth...
Hello,
We are designing a board with a npm1300 and a nRF5340. A button is connected to npm1300 SHPHLD.
On short-press, we want the npm1300 to send an interrupt to the...