Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Debugging in Segger serial example from mesh
It runs and responds to commands, but when paused or hits breakpoint - single step or continue gets to address 0xa60, continue...
While setting u p a sample project in SEGGER Embedded Studio, following error is encountered
All the previous installation steps were successful and verified.
Please...
Hi,
I am trying to implement SPI slave on NRF52810. I added nrfx_spis.c and enabled below macros in sdk_config.h
NRFX_SPIS_ENABLED and NRFX_SPIS0_ENABLED to 1
Still...
Hi all,
I am using SDK 15.3 with NRF52811 chip.
My application include app + bootloader.
In my application, I use flash area from 2E000 to 2F000 for save my user data...
hello
i want to create for the need of my project a thread border router as simple and compact as possible.
i have seen the implementation using a raspberry pi 3B as the...
Hi,
I followed this guide to send data to the GCP using the Thingy:91 : https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-connect-nrf91-to-google-cloud...
Hello,
i'm trying to set the automated test script as described here:
https://github.com/NordicSemiconductor/Android-nRF-Connect/blob/master/documentation/Automated%20tests...
Hi all,
I am a newbie in ble and also nordic. I have an application need that would do some lowfi sound data transfer which 16 bits at 14k sample rate from central device...
Hi,
Good Day!
Statement of problem: Currently we are using app_timer in our application for conducting the user behavior. For example, for user input off of capacitive...
Hello, everyone. I am newbie in use the Power Profiler Kit I followed all the steps as described in PPK User Guide v2.2:
1 - cut traces on the DK (SB40) 2 - installed the...
Hi,
I am porting a BLE program in nRF52832 EVB, and it can work correct.
The system will not work when I want to remove 32KHz crystal from my own real board.
Would you...
Hi,
So we are currently debugging our custom nrf52832 board. It is equipped with both a 32.768khz and 32Mhz Oscillator, which both SEEM to work.
I tested both using the...
What happens if I read an SMS data from a modem a while, let's say 10min, after the modem receives the SMS?
Does it keep the SMS message inside? What if several SMS messages...
Hello,
I am working on a Windows 10 pc. python 3.7 is installed and the requirements.txt has been installed successfully and I have the most current pyserial installed ...
