Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hello,
In the blinky project, I have added the following peripherals to build up an application
Timer
UART
SAADC
PPI
I have followed the saadc peripheral...
Hi, I want to use the components directory that comes with the SDK as much as possible isntead of the "packs" which comes with keil.
This is what I've selected in a project...
i have two tablets and one peripheral.Now with the code i have i connect to only one device .if i want to connect to same peripheral with another tablet i have to remove the...
Hello:
I have used the nrf52832 .when the radio have get a packet and disable the radio.I find the "NRF_RADIO->CRCSTATUS" register is "1" ,why?how "NRF_RADIO->CRCSTATUS"...
I am developing a BLE remote which will work with Android and iOS(as a remote shutter for camera). I used nRF's HID keyboard example as a base but it does not have volume...
Hello,
we are using the example ble_app_uart_c as basis.
I found out , that it takes about 650ms after Reset / Power up before i can send a string over ble.
The connection...
Hey there, I have a problem when use the command nrfjprog --memrd xxxx.
I was running a simple blinky led example on a nrf52 custom board, then i read some information from...
Hi all,
I am working on a project which receives data from UART (15 bytes at every 40ms interval). I want to store 1 minute of data on the NRF52832 RAM before sending it...
I have peripheral BLE device which can have several centrals in its whitelist. It should be able to connect to central with higher priority first, for example: device have...
Hi
I was using sdk 14.0.0. And I was adopting s332 as a soft device version and I was developing. However, when I go to Nodoric homepage and look for information, there...
I have an application for the nRF52832 which is working fine on SDK 12.3 and I am trying to port it over to SDK 14.2.
After some tweaking I have got the application ported...
I used example ble_hrs_freertos_app of SDK nRF5_SDK_14.1.0_1dda907.
I added one task for LCM (XPT2046) in the example.
i used the function :
When added the display...
Hi,
IC : nrf52832
SDK : Mesh_v1.0.0
I am testing the light_switch demo of the Mesh_v1.0.0.
I don't have 32kHz osc on my server board, so I have to change the clk...
Connect USB to PC, no "JLINK" device. But connect USB to PC and press reset button at same. I can see "BOOTLOADER" device.
How can I get my board to normal?