Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello, while writing a simple uart application, I noticed something peculiar in my code. I add led toggaling so I'd know if the code runs or not. I forgot that I disabled...
When upgrading the firmware of 54H20 using suit, compilation errors occur when calling the flash operation functions (flash_area_open, flash_area_erase, flash_area_write....
Hello. I get an error when trying to add a build configuration for a project based on a blink for a custom board on the nrf 52832 qfaa chip. Please tell me how to fix the...
Hello Nordic Team,
I am using my custom board, which uses nrf52840 qfaa chip. I am working with nRF Connect SDK v2.8.0
When I worked with blinky project on nrf52840DK...
Hi,
piggying-back on BT nus shell sample (workspace project), I try to define my own dt nodes.
I keep getting error like devicetree error: /aliases: undefined node...
Hi ALL,
v2.8.0,NRF54L15DK,I would like to ask：
1. if my pin is P0.00, is nrf_gpio_pin_set(0) correct？
2. If my pin is P1.01, is nrf_gpio_pin_set( 33 ) correct？
Hi,
I would like to flash the ad sample on Nrf54L15-PDK
Flash ends with error messages:
build messages:
I'm I tried running west flash --recover.But it didn...
I have completed a mouse program with 52840, but there are some problems at the moment. On some computers, usb will fail to obtain the descriptor, but there is no problem...
One last issue to crack. This one has been in production for a while and hasn't caused any issues other than a little annoyance to the customer. By my measurement when RTC...
Hello,
In regards to the nRF Connect SDK...
I am looking into the possibility of switching out the current implementation of AES used by the Bluetooth firmware. I am curious...
the pin for XL0 and XL1 is P00 and P01
but in my project, I need P00 and P01 works as UART.
I set the parameter to start inner RC clock.and find that: LFCLKSTAT show the...
my costom board is based upon the BT840F fanstell board. I know that this board is based on the nrf52840 QIAA SOC. but I also understand that nrf52840 QIAA has different configurations...
I am working on custom hardware with an nRF52840. I have added the MCU boot in my earlier development as well but this issue I have never faced before.
Problem statement...
Hi,
iam trying to write the data in nvs which i give input through GATT.i can read and write in nvs when not using gatt,BT.
I have 2 codes,1 is working but without GATT...
Hello,
Board: custom board
Soc: nRF52840
SDK: nRF Connect SDK v2.8.0
I would like to know device mac address and use the mac address in advertsing.
can you please...
