I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
I am using the Create a new board function to specify a simple nRF52840 based board with GPIOs using nRF Connect SDK v2.8.0. No matter how I answer the questions in...
I'm using the nRF21540 DK with the Power Profiler Kit II in ampere mode for measuring current draw. I had the gain set to +20 dBm for testing but I noticed the system was...
Hi,
We have five NRF5340DKs with us and off late it seems three of them does not get detected by the PC. In fact, what i understand is that the interface MCU seems to be...
Thingy:91X rev 1.0.0
NCS 2.6.2 own custom application
Quiescent current measured with PPK II and extension board:
nRF53x 2µA, OK
nRF70x 0µA, OK
nRF91x 17µA, OK ...
Hello,
We are in the feasibility phase of updating a product to include a nRF9151 modem connected to a nRF52840 via a single UART. The modem will operate in SLM (Serial...
Hi,
Today the nRF Connect extension isn't working anymore: it doesn't show or let me select an SDK or toolchain.
I have tried on 2 separate computers where it was still...
I am using the latest (I believe) nRF Connect for VS Code extension, version 2024.12.55. But when I "Create a new application" and pick the ncs-example-application, it only...
Our nRF5340 application requires a lot of serial ports, but 2 of them are only used for a second during configuration and are otherwise (99.9% of the time) idle. If we could...
I am a complete newby to Nordic parts and the VB design environment so please bear with my ignorance. I have just purchased a nrf52840 development kit and have successfully...
Hello,
in an earlier entry I was asking about getting multiple BIS streams, where you led me to the nRF Auraconfig Sample.
I am now using this sample and got it to run...
I'm in the process of migrating my project from NCS 2.6.1 to 2.8.0.
My project consists of a BLE application with MCUBoot as the only boot loader.
I've already updated...
hello,
I Have two nRF52833 that I have communicating over BLE. I am using soft device S140. I have my data packets use the default data length maximum of 20 bytes. I am...
I found a link
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/matter/overview/integration.html
which says MATTER protocol support is available with nrf...
nRF5280, nRFSDK 17.0.1, SoftDevice 7.2.0
The nRF52840 data sheet describes the RADIO->FREQUENCY register this way:
And describes the legal values for it in this...
Hello,
I have an application running with a BLE peripheral and our proprietary TSCH wireless stack using an integrated radio. The hardware sharing is done through the MPSL...
