Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello
I am at the early stage of evaluation of a nRF52840 USB Dongle and I have installed all software on my Win 11 PC.
Just trying to check that everything is working...
We have made 2 partition of Internal flash. One is for running Application and Other for storing some configuration. I am trying to erase the page of 2nd partition, and it...
Hi,
I have been performing a fresh install of the toolchain following the nordic's "nRF Connect for VS Code" page, as well as the YouTube video "Introducing nRF Connect...
Hello,
Developing a custom board with nRF9160 as application CPU and nRF52810 as BLE Controller. Connected via SPI + reset + irq lines to the 52810. The design is a copy...
This might be a simple one to answer but I'm struggling to find documentation on what to do here since we're still using an ancient SDK on 9160.
I have a working board file...
Hello,
We have a BLE connection issue. We want to connect a Windows 11 laptop with a nrf5340 eval board.
The connection procedure can fail by a disconnection with reason...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
I want to implement secure connections for a device based on the nRF52832, protected by a PIN/pass key, which I need to be able to configure dynamically, not hardcoded in...
Hi there
I am struggeling to find a solution to automatically connect to the controller when found based on the advertised name. I do not want to click on the found device...
Hello,
I am developing project on ESP32, with nPM1300. I am interested in battery state/capacity measurement provided by the Fuel Gauge example. Some part of the algorithm...
Hello. I followed the steps in the video to develop a project on my custom board.
www.youtube.com/watch
I created a new board and new application (blinky sample). Then...
I encounter problems moving to VScode + nRF Connect extension. Even the simplest step creates countless problems. I followed the official NRF tutorial on youtube and nothing...
Hi, in the development kit of nRF52840, the oscillator for the micro is configured as follow
In the bom, it can be seen that the used oscillator is the MP06003 that correspond...
To advertise a *configurable* device name the previous guidance seemed to be:
prj.conf
Code Snippet
Please note I have intentionally removed all error handling...
Hello,
I have multiple UART devices connected to various pins on my nRF5340, but due to hardware limitations, I can only use two UARTs concurrently alongside interfaces...
