I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Some of the products we produce do not work after about 10 days. Our firmware starts the watchdog module as soon as it starts, and sets the timeout period to 30s. And read...
I would like to implement ANALOG Modulation schemas on nrf52 serias family (e.g. AM, FM, SSB)
Do I have a direct access to IQ samples OR basic properties of the radio carrier...
I am using is25lp03d flash with "nordic,qspi-nor" driver.
The issue is that nrf_qspi_nor.c driver uses `nrfx_qspi_mem_busy_check()` before entering suspend mode. This function...
The %XCONNSTAT read command returns the total amount of data received/transmitted "in kilobytes". By kilobytes, does the documentation mean 1000 bytes or 1024 bytes?
Hi
I would like to have a project using 52840 witth softdevice 17, and I need to use internal flash to make a USB mass storage device
I reference to ....\examples...
Hi,
I need to create partition of size 4kb but using psa_ps_set() I could not able create partition of size more than 1Kb, If I try to create 4 kb Partition it's throwing...
Hello,
Creating a simple project in nrf connect 2.6.1 I start with looking at power consumption.
I need upgrade over USB, so I have added this to .prj:
In the...
software: ncs 2.5.0, zephyr\samples\drivers\counter\alarm
hardware: nRF52840dk
Step1: main.c is not be r evised!!!
Step2: prj.conf like this:
Step3: overlay file...
Hi Nordic Team,
I am currently working on a project that involves two devices, both using the nRF52840 microcontroller.
Current Setup:
Device A : I have successfully...
hello Nordic
we are working with ncs v2.5.0 trying to migrate to 2.7.0
1. so that there is several rcs, should i take v2.7.0-rc3 or v2.7.0 ?
2. while choosing v2.7.0...
Hi all,
I wonder if nrf9160 has a built-in temperature sensor interfaced with the ADC, that could help to diagnose the internal chip temperature?
Thanks.
I would like to use the Power Profiler app (with PPK II) as a pure coulomb counter for accurate long term (> many days) cumulative device energy consumption without saving...
Hi there,
We have a product running on nRF5340 with an existing workaround that was carried over from an nRF52840-based product, where SAADC readings are prevented from...
Hi Nordic Team, I'm currently working with the nRF5340 Audio DK to broadcast multiple streams, where the receiver can select which stream to listen to. To the reciever, this...
I have an ILI9340 connected to an nRF53 and want to use LVGL in Zephyr (NCS 2.6.1), but I got no label, etc. showing up. Instead, the display is showing a white screen.
...
