Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Good morning,
I ended up changing the design to use the nRF52810 chipset and I wanted to find out if Nordic would be able to provide some schematic feedback for my design...
Hi Nordic expert,
We are K5DET1/3/5/7/9/11 output high level, then string 10K resistor, K5DET2/4/6/8/10/12 through the mercury switch to read this high level, while adding...
Hi,
According to the documents of NCS, CoAP Server sample uses native OT CoAP API while CoAP Client sample uses Zephyr CoAP API, and the Zephyr CoAP API is recommanded....
I've googled all over, and I'm having a hard time finding any documentation that digs into how to use the nRF Connect SDK. Most documents point to examples, however the wealth...
Hi，
I developed with ncs 2.1 samples esb ptx and prx using nrf52840 make a low latency application，There are two problems
①On the ptx side, packets are sent twice in...
Hi, in our project we have to send some raw data to one node to other node using zigbee. So i have checked every single example but it doesnt match with what i need. I have...
Hi,
I'm trying to write a simple python application on Windows 7 that communicates with a BLE peripheral running Nordic UART Service. I'm using the nRF dongle and pyserial...
Hi,
I'm trying to config my SAM-M8Q with an array of HEX.
It's work beautifully with app_uart_put like the picture below.
However, when I try to implement LIBUARTE...
Hii
I have a problem pass the address while advertising
I should pass the adress using 9160_dk
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART...
Hi there, I'm trying to find a hardware integration guide that details min max specs for the IC and also details the RF output pin impedance so I can match to my board stackup...
I checked out the nrf github repo and tried to build the nrf_dm sample for the nRF 52840 dev kit which is what I have
In VSCode I chose "Add an existing application" and...
Hi,
As the title, I can see Mesh Proxy service in nRF connect app, after provisioined device by nrf Mesh app. But when I send data to Mesh Proxy Data In, It disconnect immediately...
I followed the document and downloaded nRF Connect for Desktop in Ubuntu 18.04.5.
Then I changed the permission of nrfconnect-3.11.1-x86_64.appimage to "allow executing...
Hi,
We have an issue that is puzzling us.
The symtoms are the following.
If we flash v1 of our application (using Segger Link) to our target, it works correctly, no...
Hello,
I am experiencing a power issue after the first ADC sample is triggered. Sampling 2 ADC channels using PPI and TIMER as the triggering mechanism. Here is a capture...
