Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi,
Because I am not getting any answers to my original ticket(ID: 294922), I'll try it this way by opening another ticket on the same issue.
I have a nrf9160DK and flashed...
Kind folks,
Situation: The product page for the Thread Topology Monitor v1.3.0 lists the following compatible dev kits (to which I've added the PCA numbers):
nRF52840...
Hi, is it posibile for use nrf21540 in the other brand BLE MCU board? some custmer maybe do not want use Nordic BLE, but want use nrf21540+other brand BLE, it is posible to...
hello!
I want to use Jlink to download code to a NRF52840 chip as MCU development board, but the number of pins and pin spacing of my Jlink are different from it. So I had...
Hi, Nordic support,
I have built success with the example "nrf5340_audio" set the gateway mode. when I run the example into my board "NRF5340 Audio DK" I get this error...
Hi,
I'm trying to use the nRF9160-DK(Ver.1.0.0) for LTE communication and GPS location information acquisition.
I found a list of LTE antennas at this URL. However, I...
We are using NRF5 SDK 17.0.2 on an NRF52840.
I am implementing a bootloader update procedure. Our updates always store the new image in external flash. The spare space in...
Hi,
I'm interested in using this AT command to upgrade my nRF52840. But I'm not quite sure what to do exactly. I'm using nRF5 V17 SDK on nRF52840. what should I provide...
Hello,
I'm thinking of increasing the transmit strength of my peripheral device using the function provided below.
sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV ,...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
I recently installed the toolchain on M1 Mac using the automatic installation in the toolchain manager.
However, I noticed that the toolchain manager installs x86 variant...
Developing on ncs 2.1, using vs code and nrf connect extension to debug an application running on nrf 9160dk
I am connecting to aws iot core in a similar fashion as your...
Hello,
I have my BLE Gatt Peripheral application working and running.
I am developing a reader that reads BLE credential.
Application is complete. I flash the .hex file...
Hi
I have configured nrf52840 on my raspberry pi. I want this dongle to stop pairing to other device once connected and also most importantly stop broadcasting once it is...
