Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
How do I switch between being SPIS/SPIM with the Zephyr library?
I am using ncs v1.9.1. I have code that works separately as a slave or master but I need to make it dynamic...
I want to use +8 dBm TX power so I added CONFIG_BT_CTLR_TX_PWR_PLUS_8 to my prj.conf, and then realised it doesn't do anything.
I then found set_tx_power() on these pages...
The problem: We are getting a hard fault immediately after jumping from the bootloader while trying to initialize the nRF USBD driver. The fault happens in nrfx_power_init...
Hi,
We are trying to integrate a remote controller functionality for smart TV and set-top box etc, using our product based on nRF52832(nRF5 SDK). I understand that we can...
I am trying to use a SPI bus with three MAX3109 chips attached to give me 6 UARTS. My overlay is defined as follows:
& spi1 {
cs-gpios = <& gpio1 13 GPIO_ACTIVE_LOW...
Hello, I'm working on a s332 application and I need to include the DFU feature in the code. I've managed to perform a DFU on s132 applications following examples like this...
I've built and able to the run the 802.15.4 RF Phy Tester but it doesn't seen to recognize any of the custom commands. Can you provide more insight into this please?
Please ignore Product Type I selected - i set it to just select that to something.
I'm planning/designing a comm box, which needs to speak to ZigBee based nodes/sensors...
Hello
I'm a beginner. I am using NRF52 series and coding in segger embedded studio. I have modified the ble_uart example and added some extra code so that I get the sensors...
Hi,
My customer occur a problem with nRF5 SDK10.0.0, the sample ble_app_hids_keyboard.
We test the sample on nRF51DK.
We connect the DK with an Android phone, and bonded...
Hello, I downloaded the NRF5 SDK for mesh. I want to make the light switch example. I installed the server and client software on two different cards. I want to make the necessary...
I am using NRF9160 (PCA10090, 1.0.0, 2021.7) for my experiment using the .hex file of UDP example provided here ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Hi
I use the nRF52840 board and am currently working on a Matter project.
I am trying to add a cluster to an existing Matter sample project as per the link guide below...
Hi,
I am working on pdm mic integration in zephyr RTOS. I used INMP441 mic sensor. I got SPL in dB by using nrfx. I want to create a driver for this mic. Please help me...
