I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
I would like to use GPIOTE, PPI, and TIMER to do the following.
I'm using three GPIO pins. Each pin will get square-wave like signals of varying frequency. On each pin I...
Hi Nordic:
we want to add timesync function on nrf5340 ble nus.(1central + 16peripherals, 0.1ms precision )
Such as:
https://github.com/nordic-auko/nRF5-ble-timesync...
Hi,
Can I know how to set the UICR as the default address in nRF52840 SOC with SDK 17.02/17.1.0 by using nRFJPROG command line tool / SEGGER Embedded Studio IDE.
nRFJPROG...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi, i was working on a project and from one day to the next i am no longer able to flash my DevBoard.
When pluging it in it comes up as "E:\" name JLINK as always, but west...
We have a board that is to be certified by a Chinese test lab, so I need to create an image based on the direct_test_mode sample.
In Zephyr v2.0.0 I created a custom board...
Hello,
We are using nRF Connect SDK 2.0 on an nRF52832 and were wondering if it is possible to use BLE and Shockburst simultaneously? If I compile enabling both Shockburst...
Hello,
A couple of days ago I run the examples direction_finding_connectionless_rx and tx on two nRF52833dk successfully, meaning that I could see the CTE info received...
Hello,
I have reconfigured the nrf_dm sample from ncs 2.0.0 to use Zephyr Bluetooth Controller by adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf.
But then it's stuck in this...
i am using the uart0 on a nrf52840 to communicate with an quectel bg95 using async api (dma) on zephyr 3.1.
from the uart interface there are connected rxd, txd, rts and...
Hi,
I am attempting to merge two example programs together and have hit an issue with a hard fault when my timer interrupt triggers.
This works fine in the standalone...
I refer to https://github.com/alc6/nrf52-pc10040-multiperipheral-passkey/blob/master/main.c for implementing static passkey. But pm_sec_params_set() returns errCode=0x7. ...
What I've done
1) Set up ot-br on an Rpi4 by following this guide .
2) Set up a 52840Dongle (plugged into the RPi4) as RCP by following this guide .
3) Installed the...
