Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello,
I am working on to program external flash (MX25R6435FZNI - Macronix) of nRF 5340 DK board using SEGGER J-Link Plus v10.1 version.
I am following Direct mode( The...
Hi,
We are currently investigating if switching to TF-M could be a good solution for us to increase our overall product security.
Our board has one nRF5340 and one nRF9160...
SDK : S140 17.1.0
CHIP : nRF52833
I try to write and read data by SPIM0.
Wirte works find but when read data oscilloscope like this.
But, receive buffer data...
Hi everybody,
I have some (probably) easy to solve issue with nRF52840 dongle s .
I've got from my company's collagues few dongles. With one of them I have some issues...
I try to run zephyr direction finding cnnetionless rx example, but i get some problem. every time into enable receiving of cte , i got assertion fail
this is my prj.c...
I visited the Community and wanted to up vote a post but found I had no rights to reply, post or up vote yet in the Welcome it says if I am a member of Devzone I can post...
I am trying to save data by using the setting subsystem of nrf connect sdk, and i <init> and <register> the settings, and when the setting_load function excuted, the h_set...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
I have followed the tutorials step by step on youtube( nRF Connect for VS Code, 1: Installation - YouTube ),but i still meet some errors when building the application.
The...
I'd like to use a nRF51822-based Bluefruit LE Sniffer to read BLE advertisements (embedded with sensor data), using a python script rather than Wireshark. I've tried pyshark...
Hello,
I have recently begun to use VSCode under Linux to develop with the nRF Connect SDK and have noticed a discrepancy in the extension's functionality when using Linux...
I would like to use the GPIO and SPI NetCore of nRF5340. Is there any example code ?? Is it necessary to disable the GPIO and SPI of the AppCore of the nRF5340.
nrF5340 Appcore sw based on peripheral_lbs and netcore sw based on hci_rpmsg are working fine. However, the appcore sw will crash when I set
CONFIG_LSM6DSO=y in the pro...
Hi,
I am running peipheral_uart sample with nRF connect 1.9.1 . After running the sample for 10-15 min, I start getting the following error
"Not able to allocate UART...
I am unable to achieve low power after I enable UART. I disabled UART0 after enabling and the UART0 registers are all getting its default value after disabling.
But the...
