I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello dear People,
I would be very happy if anyone has an idea how to solve this.
The Problem is the following: I am using nordics lte link controller to connect to nb...
Hi,
1.) I am programming a custom board based on NRF52833 using NRF52833-DK using SWIO/SWCLK interfaces using Segger Embedded Studio with NCS v1.6.1. I am trying to print...
1. Your documents mention only SPI3 and SPI4 are available in non- secure mode.. which means spi-0,1,2 should not be available in non-secure mode.. But if i use nrfx drivers...
Hello.
It is under development using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I'm currently considering Flash Data Storage (FDS).
As settings, "FDS_VIRTUAL_PAGES...
Hello.
Target nRF52832( nrf52dk_nrf52832)
SDK NCS v1.9.1
Build : SES for win 10 (5.68)
1. Support BT5.3
My project used nRF5_SDK_17.1.0_ddde560. Recently I found...
I am using a custom board design with a Nordic nRF52832 and have implemented the Nordic time sync algorithm outlined here ( https://github.com/nordic-auko/nRF5-ble-timesync...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
Hi Nordic,
I met a issue on BUS FAULT , which caused by queue.
It core dumps that:
[2022-03-22 15:35:12.657] [xxx]index = 6,len = 158 [2022-03-22 15:35:12.660] [xxx...
Hi all,
I'm a beginner and planning to import Android-nRF-Toolbox source code from Github into Android Studio after reading the README by the following steps:
1. I open...
Hi Team
In nRF52
According below picture the only the power on reset and brownout reset can reset SWJ-DP. Do we have any other method to reset the SWJ-DP.
By the way...
Hi there, We have a product using an nRF52832-QFAA, with the SDK15.2.0, the 132 Softdevice, and an application based around the Nordic UART service (nus). Customers are reporting...
