Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi
I want to use app_uart_put() to send an array which is over 4096 bytes.I try to change the value of UART_TX_BUF_SIZE to 10K bytes，then call the app_uart_put() to send...
Hey
what are the downsides of using the already burned-in Random Static Device Address compared to a Public Address?
My assumptions are as follows:
Pro
Con...
Hi,
I have been working on Zephyr for the past weeks and have been able to set multiple GPIOs, interrupts and RF functionnalities. But so far, I thought I could handle...
We'd like to use Thingy91 to measure temperature, but it looks like the thermometer (BME680 onboard) gets heat up, when Thingy91 is running for some time.
I placed the device...
Hi,
I'm supporting a customer who is planning to use T-Mobile as their carrier. One of T-Mobile's questions is:
APN requirements: Private APN requires an IPSec VPN or...
Hi,
The spi_config structure zephyr provides is as below: Wherein cs is initialized to the chip select pin. In my project I have a requirement to handle 2 slaves which...
There is a bug in the sample/nrf9160/at_monitor, namely to do with +CEREG unsolicited notification handler called "cereg_mon". "cereg_mon" expects 0-2 +CEREG status code,...
I'm trying to replace a RS232 cable with a BLE bridge with the Nordic Uart Service.
One nRF52832 configured as central (app_uart_example_central) and an other one as peripheral...
Hello,
We are working on a product that contains nRF51822. The product sends continuous data (2 bytes) via NUS service to the mobile app at a frequency of 200ms.
When...
Hello,
I am aware that this is not an Arduino support forum, but if I'm not violating any rules, I'd like to ask a question in hope that someone might have provide a helpful...
I'm developing on an iMac M1.
Over 2 month I tried to get the nRF Connect for desktop (V3.9.3) running on my M1-mac, without success.
Toolchain manager (v0.10.3) works...
Hi Nordic Team,
Currently we are exploring nRF52840 DK.
We have observed BLE Enable SOC usually have two cores, one as an application and one as BLE Soft Device core....
Hi - I am using the /nrf/samples/matter/lock sample as a reference template to develop my own app. Thank you for providing it!
I am able to build and flash the basic build...
After updating the firmware on NRF9160 Connect DK (using mfw_nrf9160_1.3.1.zip as well as the ltem asset tracker hex file) LED 3 does not turn on and AT commands in LTE Link...
