Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
just recived this kit, I ordered it some time ago but were no stock.
Problem is that software doesn't detect the hardware under "SELECT DEVICE". The device has...
When flashing files from an iOS device I run a lot into data size errors (not always), when using the same files on Android they can be copied without a problem.
It looks...
Hi,
I built a ble_app_buttonless_dfu_pca10040e_s112 project on the nRF52805. However, I cannot receive Bluetooth signal on nRF connect.
I have attached my generated hex...
Hi,
In an application with a nrf52840, we measure the frequency by counting rising edge with PPI linking GPIOTE EVENTS IN and TIMER TASK COUNT
GPIOTE.EVENTS_IN -> PPI...
Hello everyone,
I created my first own layout design and the antenna. Before I order the PCB I hope you guys can review it one time. I tried to get the most informations...
Hi all.
As per subject, I'm unable to follow device using PCA10040.
Everything was set according the latest documentation available ( infocenter.nordicsemi.com/.../nRF_Sniffer_BLE_UG_v4...
To the kind attention of Nordic support team,
we are planning to use nRF5_SDK_17.1.0_ddde560 and nRF52820 for a project. We are interested in using gzp gzll library compiled...
Hello
I'm working on a project inspired by the ble_thread_dyn_mtd_coap_cli example and for which I added the management of BLE LE Secure Connections (inspired by https:...
Hi all,
I observed an issue after upgrading to 1.8.0 and to Zephyr 2.7.0-ncs1 respectively. When having Zigbee (and NET core) enabled, all images are built as before. The...
Hello there,
I've set up 1.RaspberryPi with an otbr docker container.
Thanks to Sigurd I have set up 2.nRF21540DK running CoProcessor firmware built with nRF Connect SDK...
Hi,
I want to know more about composition data size. As I have read in Mesh Profile v1.0.1, composition data page 0 is mandatory, while the other pages are optional. The...
I have custom board defined in DTS file. There will be multiple variants of boards, therefore I need to check which board is selected. How to check which board is selected...
Hi,
We are using nrf52840 for custom design and we have replaced the mx25r6435f qspi flash with Cypress S25hS512 qspi flash. We configured the flash as below in the dts...
Hello,
We have nRF52832 devices in the field, and one of the leading causes of warranty returns is that flash of nRF52 is completely erased. nrfjprog --readcode and --readuicr...
Hello,
We have a problem that affects a few devices (< 0.1 %) in mass production. The devices are flashed, boot up and pass tests and get shipped to customers. Some customers...
