Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I see in the nrf9160 1.2.0 AT document there is a command XFILEWRITE that suggests the GPS almanac can be written and persist in the modem.
Can you provide more documentation...
Hi, I have developed firmware on nRF52840 as a peripheral. Now I have to develop firmware on nRF52832(beacon) as central which scans the first device and connects and sends...
Hi,
I am using Zephyr configured to use the softdevice as the BLE controller.
I am looking to read and write a small amount of data to the flash for non-volatile storage...
I use nRFgo Studio 1.21.2.10 and J-Link V5.12f.
In nRFgo Studio I can erase my nrf52. However, programming with softdevice or application ends with error Unable to find...
Hi,
We are having custom HW and having NRF91DK and NRF52.
We have architecture as NRF91 and NRF52 (Central) is connected over UART and NRF52 (Central) and NRF52 (Peripheral...
Hi
I'm using direction finding connectionless_rx project from NRF Connect SDK 1.7.1 with NRF52833 and I want to sample the CTE with a 4MS/s sampling rate (sample spacing...
Hi, I have a project developed on Visual Studio Code and PlatformIO. Now I want to use the same classes with SEGGER Embedded Studio. How do i do? Thanks.
I am very new to this product and Bluetooth technology in general. I am trying to determine what I have done wrong. I have purchased the nRF52 dev kit and downloaded and installed...
Hi,
In our design we use Fanstel BM832 module, based on nRF52832 chip. We have failed spurious emission in ETSI RX mode. Rx LO at ~4958 MHz exceeds the limit by 0.3 dB....
Hi,
We are working on the iOS App development for our BLE device. Our query is that, “we have completed the connection with Ble device with our iOS application on first...
I am using a setup with a PCA10040 with the PPK as piggy back. I also use a JLink Ultra+ connected to the "Debug in" connector on the PCA10040. I have cut the SB20,21,26,27...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I had tried to advertise in TLM format (in temp variable) of eddystone value coming from sensor ssts751 integrated with my devkit but not getting correct. Please suggest me...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough " RSSI > -40 " and initialize...
Hi all,
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My development board acts as a slave, while an app that tries to connect...
