Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I was wondering what examples we have in nRF Connect SDK (NCS) for firmware updates over BLE and serial (receiving an image from another device over UART). Specifically...
Hi
I have bought NRF5340-PDK board to study BLE-MESH. I found that there is 2 development tool in Nordic website
1. nRF connect SDK
2. nRF connect for Desktop
...
Hi,
I have a custom PCB that uses the nRF9160 and an RGB LED. I want to drive this LED with PWM but it uses an active LOW style of GPIO drive. I have been able to use normal...
I'm using nRF52832 with SDK v15.3 and S332 v7.0.1.
The Wireshark capture snippet shows our product connected to an iPhone using our proprietary service with a single notification...
I am using the nRF SDK v15.3.0 example project ble_app_rscs on a PCA10040 development board. I am trying to determine the functionality I need to port to my pre-production...
I would like to get timestamps with ms accuracy in order to compare it with power measurements taken simultaneously. The +CCLK command accuracy is in seconds and there are...
Hello, I am currently working on a nr52840 s140 Sdk 17.0 (dev kit) and a m using the peripheral/uart example code.
The UART TX & RX works perfectly when connecting to a...
Hi,
Quick questions regarding MAGPIO setup.
We are setting up MAGPIO pins via AT commands for RF switches.
Should the AT sentence for setting up MAGPIO be the same...
For a customer we're trying to see if we can build an IoT solution with nrf9160 to periodically send a status update to the cloud. Unfortunately, the devices are typically...
Hi everyone,
I suppose that this is a simple question but I cannot figure out what I am doing wrong. I am trying to set up an interrupt for a GPIO
I call the createInterrupt...
Hi ,
I am working nrf9160 project. I am facing error while downloading the project.
I followed the ticket - https://devzone.nordicsemi.com/f/nordic-q-a/50422/how-send...
Hello together, I am trying to work with the SEGGER software and would like to test it with a Sample from the nRF Connect SDK.
I've installed it over the Toolchain application...
Hi, I want to transfer 900KB file from mobile to NRF52.
I am using nRF5_SDK_15.3.0_59ac345. - Can you guide me for that? - How BLE receives a bin file from DFU via the NRF...
Hello, Following is my development environment IDE: Segger SDK: 16 SoftDevice: S132 Right now, we are trying to merge the following two examples. - examples/peripheral/nrf5...
