to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hello,
I'm using ncs 1.2.0 and trying to compile sample projects like v1.2.0\nrf\samples\sensor\bh1749, also v1.2.0\zephyr\samples\sensor\* but all the defines for device...
Hello,
I'm trying to setup interrupt routines in SPIS1 peripheral.
I have a void IRQ function
But it seems like it never gets called
my init function
some...
Hi,
As I understand Nordic NCS now supports nRF52 development for nrf52832/40/11/10, so based on this I am trying to make a simple application for nRF5232 chip (peripheral_uart...
Hello,
I've been using http/https for some time with Zephyr, and am now venturing into using LTE/NB-IoT on a NRF9160DK board.
Unfortunately, from what I can tell, the...
Hi,
We are working on a Thread network application using nRF52840 DK and would like to interface a WiFi module to this board. We have checked the DevZone and found one similar...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi,
I have added the Buttonless Secure DFU service to my application so that the app can be updated over BLE. It seems working. However, the power management module must...
Hi,
1. In my last post, ( https://devzone.nordicsemi.com/f/nordic-q-a/60300/questions-on-usbd_cdc_acm-example ), in question #1 a nice explanation was given regarding the...
Hi,
I am wondering if there solution available to perform DFU using Windows 10 OS? Going through previous tickets, it seems that there is no easy solution to perform DFU...
Support,
I am using the ble_app_gls_pac19956_140 example on the nRF 52840 DK. I wish to use this application as a foundation for my new sensor.
I wanted to disable the...
SDK: 15.2 IDE: Keil Softdevice: S132 v 6.0 General question about PPI connections. Is it possible to setup a PPI channel, that when triggered by some event (e.g. value in...
Hi,
I'm trying to lower the power consumption om an Actinius Icarus board which uses an nrf9160 chip. I've been able to achieve a sleep current of 1.33mA and I'm not able...
Now the code in the application part has added the buttonless_dfu function, which has also been successfully implemented. But I ’m not familiar with serial_dfu, I don’t know...
Good Afternoon:
We are developing a BLE remote button using Nordic's nrf52840. We have purchased several devkits and are in the process of fabricating our own design specific...
