Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hi,
I'd like to update firmware on my nRF52832 panel with my update flow (only the application; the bootloader and softdevice will be unchanged). I can load the new firmware...
I cannot step through source c code, only disassembly. This only applies to custom source, such as main, that appear not in the SDK file folder but the code that resides in...
Hi,
We are developing an android application using nRF51422 to connect the BLE device, discovering characteristics and sending commands to the device. Here we are facing...
Hi, im working with the Arduino Example called pingpair ack. Sometimes I get this "Blank payload". ¿What does it means? The message was correctly recieved?
Sometimes I get...
Hi!
I'm not good at C and microcontrollers programming. Could somebody clarify, if nrf_rtc_counter_get interrupt safe? It just reads value from rtc register->COUNTER (24bit...
Hi,
When I enabled NRF_BL_DFU_ENTER_METHOD_PINRESET.
The 52840 Dongle into the DFU mode every time hardware power reset.
Use other DFU enters method does not have this...
There are so many references to this, and so many versions for each DeviceFamilyPack, but literally not one mention of how or where to install this.
Can someone help me...
Hi,
I'm using two nrf52 dev kits and the ble_app_uart & ble_app_uart_c examples to test a BLE link that would ideally be able to hit a 1Mbps throughput. I am, however, very...
I am scanning beacons data in ble central profile with gap scan parameter
static ble_gap_scan_params_t const m_scan_params = { .extended = 1, .active = 1, .interval = 0x640...
Hi,
I am using modified MQTT simple code on a DK board. I am wanting to "capture" URC's. For testing I have enabled CEREG and CESQ URC's and disabled the AT host library...
Hi,
nRF9160 DK I have a simple question regarding processing at command responses. I was hoping to extract the individual values from a at command response using the at...
Hi,
We are designing our custom board with NRF52840 , we need to add serial capabilities over USB.
We were thinking about adding FTDI Chip ( FT232H ) connected to the...
I have been using SEGGER studio 4.22 on my MacBook for a while now. Today I went to open my project and it said I didn't have a license. I chose continue and it just opens...
Hi,
I have Power Profiler Board. It works on Windows Desktop.
But no on Ubuntu Machine:
Ubuntu 16.04,
nRFConnect 3.3.0 and nRFConnect 3.3.1 AppImage
Power Profile...
Feature request.
In the current Connect SDK, I must add the name of any new 9160-based board directory to ncs\nrf\cmake\multi_image.cmake.This requires anyone installing...