I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I'm using nrf52840 SDK V15.3.0 SoftDevice S140. I want to test long range feature and 2mbps mode also . How to add these features in SDK example code like ble_app_uart or...
Hi guys, i'm playing a bit with the ble blinky peripheral example, as a precursor to a bigger project.
What im trying to do is disable the services completely, meaning that...
Hi all,
I am trying to emulate a device with ble-driver-py. What I am looking is to have a device advertise, provide few services with respective characteristics (read,...
On November 19th, I participated in the 2019 Nordic Tech Tour with my colleagues, but some of the content was not clearly understood, especially regarding the development...
Hi all. I want to measure current consumption on nRF52840 DK (PCA10056).
I have the SB40 cut and the 12 Ohm resistor placed in R90. I measure the voltage on this resistor...
Dear team：
How can I use ble-bas-c to change Characteristic UUID or Connect the 1800 service and rename it with the 2A00 feature value The example is \SDK\nRF5_SDK_15.3...
Hi,
I am new to this. I want to build a mesh network using nrf52832. I have already downloaded and gone through nrf5 SDK for mesh but i am confused about what to use to...
I am using nrf51822 DK. How to set GPIO pins as output pins and access the pins to set or reset the output.For example if I want to use pin 20 as output, how to configure...
I am trying to read if an input is 0 or 1 but for some reason it takes the first one its offered and then it does not change anymore.
int main(void)
{
nrf_gpio_cfg_output...
<Environment> - nRF9160 DK v0.8.5 - nrf tag: 1.1.0 - modem version: 1.1.0 - using an external GPS antenna, SW12 => CON
I'm attempting to use udp_gps, but doesn't work out...
Hi all,
I'm a bit confused. After going through available documentation, I thought I had understood that RTC0 was used by the SoftDevice, but that RTC1 was available to...
Hi,
I am using nRFmesh SDK for a project. I have configured all nodes(devices) into one group. Each device will publish message for every three seconds. I am reading the...
Hi,
I need step by step guidance on how to implement BLE MESH ( SIG MESH) using nRF52840 Dongles.
I am trying to connect 5 dongles in MESH config.
Kindly help with...
