Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello!
I would like to use an external antenna with my nrf9160dk to be able to attenuate the signal. But I am unsure about what is needed to make it work.
Is it enough...
Hi,
I have read through this tutorials on how to develop custom UUID, and I have implemented it successfully.
But I need to have 2 characteristics. I have basically duplicated...
Hello. I am trying to use TWI with mpu9250 sensor after System Off mode. But it is not working well. Do I need to do some preparation before going to System off mode? Where...
Hi All,
I'm using Ellysis sniffer for debugging my ble mesh network.
I've made network setup using generic on/off application and I'm able to communicate and capture...
I have a nRF9160 DK and since I am in Germany, we are trying to use the most common LTE band they use here, which are:
Band 1,3,7,20
However, band 7 does not seem available...
When I compile one of the nfr_log modules (e.x. nrf_log_frontend.c) I get the following error.
I do include ../components/softdevice/s132/headers/nfr52 in my User Include...
I have an nRF9160 DK which came with an enclosed eSIM from iBasis, that is supposed to work in most of Europe.
However, after jumping through all the getting started hoops...
Hi All,
Posting this here after a lot of searching and troubleshooting. There have been a lot of similar posts but none actually seems to go into how to implement this in...
I'm successfully printing to the UART1 com port at baud rate 115200, but I have a peripheral I plan to connect that requires 9600. What is the proper way to go about this...
I'm using an NRF52840, SoftDevice s140, FreeRTOS, SDK 15.3.0.
I'm trying to sample my ADC at high speed, >1khz (10-40kHz).
I implemented the logic from the SAADC exaple...
Development environment：
NRF52832
SDK：15.3
SOFTDEVICE：NONE
When testing the FDS module power-off data protection feature, the FDS module is abnormal.
During the...
I have a PCB containing an nRF9160 using a SEGGER J-Link. I am able to update the application firmware at will using a variety of tools but if I use nRF Connect v3.2.0 to...
To the kind attention of Nordic support team,
I'm considering to get started manufacturing mini dongle nRF52840 based as in https://devzone.nordicsemi.com/f/nordic-q-a/48568...
I have the following problem:
I want to update my application code via BLE with the secure bootloader. This works perfectly while the J-Link-RTT-viewer is connected.
When...
Hello
I am using the basic asset tracker example + https://nrfcloud.com
I can see messages from the device to cloud, how can I send commands from cloud to device?
...
