Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
I am getting this error on SES "components\softdevice\common\nrf_sdh.c:164:20: error: 'SD_EVT_IRQn' undeclared (first use in this function); did you mean 'QDEC_IRQn'?" SD_EVT_IRQn...
Dear All;
I'm looking to flash a RIOT-OS image onto the Thingy52 via the J-LINK OB on the nRF9160 DK. I'm using Linux and both nrfjprog and JLinkExe detects the programmer...
I am trying to download and install nRF5x Command Line Tools for Mac OSX. When I click the link I'm directed to a 404 page not found. Could you please advise of an operational...
Hi Since we're almost done with the programming for our application we would like to move from the Development Kit to a custom board as similar as possible to the final PCB...
I am using the legacy bootloader, SDK 11.0 with SD 2.0, S132
The example Bootloader DFU images part of SDK 11.0 load just fine (I'm using nRF Connect Android app), however...
Hi, I've been recently working on trying to stablish an i2c (twi) communication between my nrf52 Dev kit and a LIS3DH located in a STEVAL-IDI-003V2 board.
In this post https...
Hi!
I have used NRF52832 on PCA10040.
I want use several pair (master and slave) in one room.
For this I try to select a different frequency for each pair.
But, when I...
When trying to use BPA600 BLE analyzer I was not able to see the LL packets. when contacted Frontline/Teledyne tech support they said I am into BLE 5.0 stack.
However so...
Hi ,
I configured nordic as slave and it looks like the transactions been successful, but when 2 SPI transactions occurs consecutively slave was setting 0xAA in return...
Hello, we are developing using nRF52840 DK, SDK version 15.2 and Mesh SDK version 3.1.0, using Segger Embedded Studio.
Currently we are using the nRF Mesh app to provision...
Dear support team,
I wanted to program and debug nrf52840 dongle through an external debugger. For that, I connected the debug out of nrf52840 development kit to the SWD...
Hi, I recently added the buttonless DFU bootloader on my device with the debug config. I am using and I can flash an application when in DFU. Although, I cannot debug my application...
Using the Mesh SDK 3.1.0 the advertising bearer's transmission interval is limited 20msec (B EARER_ADV_INT_MIN_MS).
The Mesh Profile Spec indicates in s4.2.19 that the transmission...
Is it possible to transfer 258 bytes over the TWI interface of the nRF52832 in one transaction ? The manual says that RXD.MAXCNT is 8 bit wide only. I need to read 258 bytes...
Hello,
I need help with my project. I am adding fds library to the light sw example.
I did this steps:
1. Included necessary *.h files
2. Added fds.c to the project...
