Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi There
Is there any additional drivers that i have to install to use nRF connect on my Mac?
I've installed it and when i connect the nRF9160 DK to the Mac, it doesn...
Hi, I am trying to implement app_timer library with FreeRTOS. Based on my testings, it seems that app_timer_start() under app_timer_freertos.c has the lowest time resolution...
Good day
I moved from Mesh3.00 to mesh 3.1 and I see the way UUID is extracted is slightly different.
I would like to know when I copy the UUID to use in my project will...
Sorry for disturbing!
I have some questions about measuring nRF52832 32Mhz Crystal frequency.
I use an active probe(Tektronix P6243) to catch the signal and the test result...
In the case where connecting to a phone that is paired with my device after my device has cleared pairing information and doesn't remember the pair, I'm observing the following...
I'm working on a project to get two devices to agree on a secret key based off of physical layer properties.
My solution is for devices A and B to make 64 RSSI measurements...
Hello, we have developed our product with S132 version 6.0.0 and sdk 15.0.0 since that was the most current when we were in the development stage.
However, now we need the...
When switching the dongle into DFU mode, it changes the serial port number when running in windows.
Both the bootloader and the application sets up the USB and calls the...
Hello, I am using the nRF51422 development kit. The SDK I am using is the nRF5_12.3.0_d7731ad. I am trying to run the "Blinky" example by copying the hex file for the PCA10028...
Dear Nordic Team,
we are developing a system with Bluetooth Low Energy and Zigbee capabilities (using the TI CC2630 microcontroller as Zigbee external communication device...
Hi,
In our project we have got one NRF52 as a central and one as a peripheral.
For now we are correctly connecting between our devices - periph is advertising and central...
Hi, I was wondering if there was an updated example for using the Flash Manager correctly with SDK for Mesh v3.1.0?
Some info about my setup:
Up until now I have been...
I am bringing up a breakout board for an nRF52832 module (MDBT42Q) and can not get a response from the module. The breakout board has very little circuitry, mostly fanout...
The AES tests for the CC310 cryptocell backend seem to only use the 128 bit key length.
While ECDF seems to support bigger key sizes (192, 256) AES does not.
Is this a...
