Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I would like to implement the mbed uVisor on the NRF52832 SoC with the softdevice s132.
So I created the configuration files and wrote some code.
Now I have problems with...
Hi,
I am trying to compile some RuuviTag application using nRF5_SDK_12.3.0_d7731ad
2 symbols are not defined,
APP_CONFIG_ADV_FRAME_SPACING_MS_MIN and
_ADV_FRAME_ETLM_SPACING_MS...
Hi nordic guys,
After the hid device delete the bond info but the PC did not remove it form the bond list,and i want the hid device to reconnect the PC quickly again but...
Hi,
in nrf connect app i see it is possible to update bootloader over ota.
How do i generate ota file properly? I tried generating zip and hex but the app says "no matching...
I have nRF6310, nRF2727.
I wonder if I can update the nRF24L01 firmware with the above board.
I wonder if there are any additional devices or other methods...
I am using ble_app_uart in one nRF52 EVK board(peripheral) and ble_app_uart_c in another nRF52 EVK(central) and sending data of Device under test through UART. When the data...
Hi,I want to use RTT in bootloader project.
First,i add all files(SEGGER_RTT.c ,SEGGER_RTT_printf.c,RTT_Syscalls_KEIL.c) to my bootloader project(Picture 1).
Second,I add...
hai
in nrf51822 the pins p0.01 t0 p0.06 are marked as analog pins in the nrf51822 DK.
i know that in arduino we can use an analog pin as an analog input as well as a digital...
Hello!
I am developing with mbed. According to nRFgo Studio, the hex file generated by the mbed compiler already contains the following SoftDevice: S132_nRF52_2.0.0 (Id...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I want to send data coming from uart to ble and data coming from ble to uart same as ble_app_uart example...
Hi there,
I am working on programming the CTS ble service on my code.
In order to do that I also have to include db discovery.
#include "ble_cts_c.h"
#include "ble_db_discovery...
Hi,When I use nRF Connect app(IOS version) to connect my ble device,BLE_GATTS_EVT_SYS_ATTR_MISSING log information appears in my RTT Viewer(Picture IOS_Phone_Conncet).After...
Hello,
I tried as you mentioned using sdk12.1.0 buttonless_dfu and bootloader_secure example.
I didn’t modify anything except dfu_public_key.c.
As shown in the attached...
Hello,
I have a program that do an infinite loop in sd_softdevice_enable. How can i investigate ?
Loop is from 0x00009DEA to 0x00009DF2
Target is nRF52832 AA with...
Hi,
I am working on nRF52 with freertos + SDK13.0 + sd S132_4.0.2. I found the device will be trap in the xTaskIncrementTick of the xPortSysTickHandler when some task is...
