Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hi,all!
I am programing an android ble app.And I have successfully connected to my device and get my own service(uuid:0x1600),and the characteristic in it(uuid:0x1601)...
Is there somewhere that we can see the defconfig file for the Raspbian images generated here (under downloads): www.nordicsemi.com/.../nRF51-IoT-SDK
We'd like to integrate...
Hi, When using RBC mesh and SD8.0.0 I often get assertion at line 189 in soc_radio_timeslot.c.
This file is part of sd8.0.0 and I dont have source code. Why is this assert...
Hi all,
I am trying to send data(rssi+MAC address) from GATT server to GATT client using sd_ble_gatts_hvx(). I added the service and the characteristic into the ATT table...
Hi,
Following the AN 29 "nRF51 Development with GCC and Eclipse v1.1", I cannot import any project on Eclipse for nRF51822:
In step 1.2 "Import existing Eclipse project...
I work for a small start-up. Our products monitor events and communicate via bluetooth with an Android tablet.
We are currently trying to make our custom circuit using...
I'm using
s110_7.1
sdk 7.2
DFU
updating application (application.hex + application.dat zipped) works fine, but when updating bootloader (bootloader.hex+bootloader...
Hi,Nordic support
Circuit design: Unused I/O pins
where can i found recommended I/O end terminal desing of unusing GPIO pins ?
I'd need such as pull-down resistor......
HI, I'm extremely new about Nordic component and device.
I buy a nRF51 DK for start understand hou BLE work, I attach to my pc, the green led power on and my pc know the...
With S110 v8.0.0's size increased to 96K, I'm concerned that my current memory layout is going to prevent me from upgrading to a future softdevice.
It seems that the only...
The function dfu_ble_get_peer_data seems to be declared in dfu_ble_svc_internal.h
but not defined, (not actually implemented) somewhere deep within the Nordic Software Packs...
Folks,
Simple UART communication shouldn't be this difficult. Embarrassed to admit it, but I'm having problems setting up and using the app_uart.c/.h module from the SDK...
Hi all,
I have a working prototype of a service which enables a number of characteristics for the control of motors and relays. The motors work great, and are controlled...
Is it possible for gpiote_event_handler interrupt to get executed while the program is executing code inside timer_event_handler?
These events modify same variables so...
I intend to keep a long running clock in the system and use the app_timers(hence RTC1) in a soft device enabled nrf51822 firmware.
I basically have a minute tick and update...
