Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
I was trying to receive some data using "i2c_transfer" then continue the receiving without starting a new transaction.
Stop bit was sent if I configured to use it or not...
My project has a nrf5340+external flash, and an external USB-C connector. The device exposes a USB file system (FAT) which is hosted on the external flash partition, and appears...
Hi Nordic
Q1.
HW: nrf9160 customer board. One USB-to-RS232 cable is used for PC sending AT commands (UART2).
Another USB-to-RS232 cable is used for PC collecting modem...
I am currently evaluating the Nrf54l15 viability for a migration from the Nrf52 for our products. I've been able to advertise, scan and connect with success but I can't find...
Hi,
I'm trying to build the nrf5340_audio/broadcast_source application. I'm getting the following error: nrf5340_audio/src/audio/le_audio_rx.c:20:22: error: 'CONFIG_BT_ISO_RX_MTU...
Hi, I have recently created a board definition for our nRF5340-based hardware using the "Create a new board" feature from the nRF Connect for VS Code plugin. I'm using SDK...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
I am going to do dfu not by YOUR example(FOTA or UART……)
I flash_write() data to image-1 address，and...
Hello,
Very new to Zigbee. Trying to use nrf 5340 dk as a Zigbee Coordinator to connect to a Thirdreality and a Sonoff PIR motion sensor. No modification (expect adding...
I am using the solution for this exercise to have MCUBoot use the nrf5340dk's external flash for the secondary partition in my own project. I have done the following:
1...
Hi,
I have a question about official suported Bluetooth version on NRF5340, becase there's some conflicting informations.... On this link, it's written " Bluetooth 5.4...
I have nrf52840DK less than 6 month. It has been sitting in my drawer and has some sample code in it which is detecting button press and light up corresponding leds.
Last...
Dear Nordic Team,
We just started the development with NRF54L15 EVK and fabricated and Assembled PCBs as well using NRF54 MCU.
In our product we require 4 timers peripherals...
Hi,
We are currently using the NRF52832 in one of our products. Due to software requirements we need more RAM. Therefore the product is going to be redesigned for the NRF52840...
