Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi Nordic team, We have a project that uses nRF5340 &NCS 2.7.0, and we encountered net core crashing issue each time when ble is connected by central device and 5340 app core...
Description:
Hello,
I am trying to build my project nrf_dm_testing using NCS 2.9.0 , but I am encountering a CMake configuration error. The error message is as follows...
I am using 9160 as slave which communicates with nrf5340(master) over UART. with flow control disabled everything works but as soon as I enable the hardware flow control then...
Hello,
I have a few questions regarding the nPM1300 current measurements:
As far as I understand, there are two ways to trigger a current measurement:
By writing...
I am using VS Code IDE and have installed nrf Connect Extension and done with the installation part and blinky and few other samples. So, basically I just copied an available...
I have figured out a way to realize IR communication,it is same with the way to drive WS2812 with SPI.
[ I can use PWM peripheral and should use it,for I need to change...
Just to confirm the head question.
I have found the same question : NRF52 help configuring TIMER + DMA + PWM - Nordic Q&A - Nordic DevZone - Nordic DevZone
There is no...
Hello,
1. Do you have any hardware to implement Wireless HID USB without Bluetooth like Logitech with USB dongle?
2. Do you have an example of IR TV remote for any hardware...
Hello,
NCS 2.9.0 nRF54L15 DK 0.9.1
I am trying to follow the instructions in the manual in the User Guide of the nRF54L15 DK to use P1.00 and P1.01 as normal GPIOs. (side...
Hello,
I have been following the steps in Exercise 1 of Lesson 1 of the Cellular IoT Fundamentals course. I have a Thingy:91. I have followed the steps so far
- flashed...
Hi
Long time no see
I recently got my sweaty hands on a sparkly new 54L15DK, and I thought I would try it out. The AI guided me to the coremark sample and the multicore...
I recently tired the Onomondo static and external softSim demo on the nRF9151 DK. For both of the demos they take around 4 minutes until the DK gets a cellular connection...
What is the connector cable that fits with nRF5340 DK J1, I am using the other end to connect to the ANT-B10 J2 (antenna board). I will like to know which connector cable...
I am currently trying to add MCU boot to my application using sysbuild. I have done the following :
Created sysbuild.conf in application root
Created sysbuild folder...
