Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi,
After lots of issues with build and deploy, I eventually have a working version of a BLE App running on a XM122 Radar module. This module have to be packeaged with the...
Hi devzone
there are 2 nrf52 dk board - one is client(ble_app_blinky_c) and the other it peripheral(ble_app_blinky)
and I made it so that if you push the button3 on...
I need to port some functionality that is using nRF5 SDK 17.0.2/ S332 SoftDevice v6.1.1 to an older firmware using nRF5 SDK v12.0.0/Softdevice 332 v2.0.0. It looks like Softdevice...
I'm trying to build the documentation on a Windows 10 system. I've installed all of the required tools and made it to step 4 when I get the following:
C:\ncs\v1.9.1\nrf...
Hello All,
I have a problem when I build my project from sample central_uart & peripheral_uart .
I have two nrf5340 called A and B . B scans the broadcast to A to establish...
I'm having problems reading channel AIN7 in the rRF52, SDK11
I configure every channel in a similar way:
//adc_channel_5
{
nrf_saadc_channel_config_t channel_config...
Hi I am working on nrf52840 dk project. I want to find out the maximum stack usage of the program.I searched in the devzone support forum and stumbled upon this method to...
Is there a problem with writing-to and notifying-from the same characteristic? Or is it recommended that one create two characteristics, one for receiving data, and the other...
Hi everyone,
I am using the nRF52840-PDK and nRF5_SDK_17.1.0_ddde560, And trying to enter System Off modes with no RAM Retention.
I use the ram_retention example from...
Hi,
I have met a problem that I try to advertise nRF52840 dongle in pc-ble-driver-py. However, connection is not built from this command:
The uuid is uart over ble which...
Hello Nordic family, I hope everyone is fine.
I want to do modifications to the nRF Toolbox android App such that the data received by the nRF Toolbox android App from the...
I'll start off by saying, as a new developer, Nordic has made an absolute mess out of the docs. The default example 'TWI_sensor' starts with easyDMA enabled, meaning it defaults...
Hello,
I am using nrf5340 module with external hardware audio codec to test stereo audio output.
I use nrf5340 module as the headset to connect with Pixel 7 mobile phone...
Hi Nordic Team,
The default stream direction is undirectional, so I add CONFIG_STREAM_BIDIRECTIONAL=y in prj.conf, then use " python buildprog.py -c both -b debug -d both...
Hello,
We have a fitness application that employs concurrent use of ANT+ and BLE communications on an nRF52840, that we wish to port to the nRF5340. The product brief...
